Search results

  1. G

    1990 200txesm rectifier/reg

    Did the proper test on Rect/Reg, found the tach would work after following the procedures of placing gray tach wire to Yellow/gray on terminal board, went and picked up the OEm R/R for this model. The problem is; the new one has the Red to the soelinoid, the two yellows for the stator, and the...
  2. G

    Stator and/or power pack

    1991 200 Rude, been having cold start issues with this motor for about a month, here are the symptoms; Takes 15-30 minutes too start cold, once it does fire and run, it will run fine all day long, like I said, it started this about a month ago. I dont have spark at this initial starting time...
  3. G

    V6 water passage deflectors

    1991 200 rude, does this motor have water deflectors? I did some research and cant get a straight answer, I cleaned everything and never ran across any.
  4. G

    91 200 evin looper head

    Does anyone have a picture or diagram of the water passage deflectors for this looper? Also, the head gaskets are the same, and they specify which side goes toward the head, is this correct? Or does the starboard side need to be flipped?
  5. G

    Control valve function

    91 Rude 200hp, what is the function of the Control Valve #0394407, mine is leaking at different levels of throttle, curious as to the function of this valve as its connected to the linkage.
  6. G

    VRO disconnect to mix

    Went ahead and disconnected VRO, and mixed all fuel at 50:1, did this as instructed and now seem to be starving for fuel after start up. Will run for about a minute, then starts starving and dies out, ran fine with oil line connected, just was'nt receiving enough oil.
  7. G

    91 evinrude 200 (hot)

    Good morning guys, i recently aquired a 91 200hp evinrude, and finally got it out yesterday. it ran hot after about 10 minutes, i let it cool down and got it back on the trailer. Pulled t-stats, and had the starboard side pretty gummed up, replaced both stats and the water pump. Appears to be...
  8. G

    New power pack not grounding

    88 40hp johnson, new power pack installed yet when key is turned off motor keeps running. New pack seems to not be grounding out.
  9. G

    88 DT-150 getting hot

    1988 DT-150, gets hot quick. I pulled t-stats and cleaned, put in hot water and both opened up. Have water at tell tale, but for a motor this big, I'm assuming it should be a hard stream? When i had the t-stats out I flushed water in, and had water at tell tale but not too much at intakes on LU...
  10. G

    Model year

    Just got a suzuki dt 150 with the numbers 804266, any idea year and model of this motor? It is the 12 plug 6 cyl. model.
  11. G

    Late 80's suzuki dt-150 pros-cons

    Good morning, I'm looking at a boat with a late 80's DT-150 with the dual plug per cyl. Any of you suzuki experts have any pro or cons on this motor? It looks clean for its age, has had carbs cleaned and rebuilt, and sounds strong. I've always had Johnsons or Yamahas, so this would be my first...
  12. G

    88 40hp evin. prop size

    Hey everyone, anyone know where I can find out the correct size prop. for a 1988 40 hp evinrude tracker vro. I have a 11 3/4 X 17, and the other seems bigger, I'm going to pull the other tonight and see if it's inscribed on the hub.
  13. G

    Lower unit inter-change

    Good day all, my question is, do any of you guys know which lower units are interchangable to a 1988 40hp evinrude. Also, I cant for the life of me find the model number on this motor,(painted over i guess) will the number on the head tell me? Thanks in advance.
Top