Search results

  1. j_k_bisson

    Need replacement windshield for 2003 Lund Pro V

    I am searching for a company that manufactures replacement, to OEM standards, windshields. I have a 2002 Lund Prov 1900 SE. I need the starboard side, but if the cost is not huge, I would buy both Port and Starboard. If someone can point me in the right direction it would be great. I have...
  2. j_k_bisson

    1993 Mariner 75 hp lower pivot shaft seal replacement

    Reaching out to everyone here that has ever replaced the lower pivot seal on a 1993 Mariner 75hp 3 cylinder. My seal is partially sticking out where the waffle washer is, above the lower mount. I do have the factory service manual, but details on how to change this out when the whole motor is...
  3. j_k_bisson

    1993 Mariner 75hp high pressure tell tale, not heating up.

    I recently purchased a 1993 Pro V with a 1993 75hp Mariner 3 cylinder on it. I have worked thru all the other issues with a motor this old; carb rebuilds, link and sync, faulty coils, new water impeller, new fuel lines, removal of oil injections system, etc.... My current problem is a rough...
  4. j_k_bisson

    1993 Mariner 75 hp Carb idle setting - Which Way is Leaner?

    I have a stupid question for everyone here. I have a 1993 Mariner 75 hp - three carb - motor. I have purchased a Factory service manual and have read all the sections of setting the idler jet screw. It states, initial setting 1.5 turns out, in water, in gear, warmed up, turn in each idler screw...
  5. j_k_bisson

    1988 4 hp Johnson Sailmaster adding tell tale water drip

    Has anyone ever added a tell tale water line to a 1988-1991 4 hp Sailmaster outboard. Model number J4RLCCS. I was thinking of drilling the Exhaust Cover plate where the water line passes by it at the top. I was going to use a 10-32 UNF x 5/32 Barb 90 degree fitting. This would only require a #21...
  6. j_k_bisson

    1988 Johnson 4 Hp Sailmaster operating perimeters

    I recently acquired a 1988 Johnson 4 hp Sailmaster (J4RLCCS) that is in near mint condition. I have purchased a factory service manual and have rebuilt the Fuel Pump, Carb, primer/choke system and installed a impeller rebuild kit. I can get it to run great at both Idle and High RPM's. My issue...
  7. j_k_bisson

    Ram bow mount trolling motor stabilizer

    I recently purchased a 1993 Lund Pro V 1775 with a 2007 Minn Kota Power Drive bow mount trolling motor. I have been told by a fishing friend that with the addition of a Min Kota quick change composite bracket, I now need to have a Ram mount head stabilizer. They stated that the head that is...
  8. j_k_bisson

    It Lives!!!! Thanks For everyone here....

    For those that have been helping me out to resurrect my old 1981-1983 (? Unconfirmed) Honda BF75 from the outdoor rack in the back yard where it has sat for over 7 years in the elements. Thank you for all your help! It is appreciated and this is the place I always come for help. What a great...
  9. j_k_bisson

    Pre-1997 Charging Cables for BF75

    Looking for help locating an accessory part for a Pre-1997 BF75 Motor. I have tested the charging circuit on the motor and it is producing power, I would like to buy the accessory plug/cable to be able to charge my battery while I chug along. I have found the block off plug for the motor port...
  10. j_k_bisson

    Can't figure it out, and its costing me money!!!!! lol

    Looking for help from the community here in identifying the fuel connector I need for an old pre-1997 Honda BF75 (BF75L 1301753). I ordered part number Seachoice 20441 LC, which says it is for Honda part number 17650-921-003ZB. Well it does not fit. It has 2 issues, 1 the retaining stud is round...
  11. j_k_bisson

    Is there truely a difference between a Tohatsu and a Mercury 6hp? Then what?

    Been looking at replacing the Honda pre-1997 BF75 with a new kicker motor and have zeroed in on the Mercury 6hp 20" long shaft I talked to a couple of guys at work and they state that the motors are identical. I read online that the power heads are the same, but the lower units and carbs are...
  12. j_k_bisson

    Can you soak it too much?

    I thought I would ask here the question everyone has wondered at one time or other. Dose it matter how long I soak a carburetor in Varsol? I current have a carb (disassembled) soaking in a container for the last 4 days and don't plan on pulling it out and cleaning it until the carb kit comes in...
  13. j_k_bisson

    1993 Lund Pro V Rear Livewell drain tube size

    Looking for anyone who know sizes for the rear live well drain size for a 1993 Lund Pro V (Tiller). Both diameter and length required for proper operation. When I bought the boat, one did not come with it. Only a recessed drain hole that is difficult to measure. With looking at what is out...
  14. j_k_bisson

    Glueing gage back together

    Recently had my battery level indicator gage for the 1993 Lund Pro V come off with the glass face. After reiving the gage (removed from boat) and all the parts (glass, rubber gaskt, and retaining ring, it appears that the glue finally let go. I have hold it together as it was originally with...
  15. j_k_bisson

    Looking for help identifing Year - BF75L 1301753

    Looking to uy a service manual for this motor that is new to me, and need to know the year of this motor. The serial number tag says BF75L 1301753 I need the manual to set the timing where the belt on top is. One of my kids pulled it off and I need to set the timing again, along with cleaning...
  16. j_k_bisson

    93 75 hp Mariner - Oil Injection disable / bypass

    Watched a couple of U-tube videos on how to by-pass the oil injection system on my 1993 75 hp Marine. All they do is disconnect they wires from the oil sender in the oil tank and remove the oil pump drive shaft. Then Plug/cap the oil lines to the fuel and oil pumps. Questions to everyone here...
  17. j_k_bisson

    Alarm - IS it bad?

    I have a 1993 Mercury 75 hp that the alarm was not sounding when I bought the boat, so started trouble shooting and removed the alarm, and tried testing it. When I make the + and - contacts to the battery directly, the alarm horn momentarily crackles once power is applied. No Buzzing sound. Does...
  18. j_k_bisson

    1993 Mariner 75 hp 3 cylinder tiller, can't find alarm under hood

    Just bought a 1993 Mariner 75 hp 3 cylinder tiller on a Lund Pro V. When I turn the keep, I do not hear any beeps or anything. I Ordered a factory service manual, but don't want to wait for it to come in. So I thought I would ask here where it could be located. I looked up online to find what I...
  19. j_k_bisson

    93 Mariner 75 hp

    Looking to get back into boating again after a couple years of doing without. I'm looking at a boat with a 75 hp Mariner 1993. I was hoping the community here couple give me some insight to this motor. Are there known issues with these motors? (read that the stators are not the greatest)...
  20. j_k_bisson

    Looking at a new truck......

    I understand that asking this question can develop into 100% opinion based bais. I am looking for facts and stories. I am looking at buys a new 2012 Chev Silverado. It has a 5.3l vortec aluminum block motor. I am a Ford guy switching to a chev. Let's not go there..... I am asking if anyone has...
Top