Search results

  1. S

    1993 cobra lower unit ?

    I was wondering if the lower driveshaft pinion gear bearing should be caged or not?upon disassembly, I see mine is not.but looking up the part ,it looks caged.??
  2. S

    Year by ser #

    Is there a way to tell the year of my out drive by this number plate?? Top numbers are,987343 then says 3.0l,then at bottom T0779120 ( in case it's blurred)
  3. S

    Bearing carrier removal 1989 cobra 3 litre.

    So trying to pull the bearing carrier on my cobra.took off 2 bolts and 2 tabs that seem to hold it in.made 2 threaded rods for my puller,comes out ok for 1/4 inch then gets tight and stops.? Am I missing something,manual is kinda sketchy( seloc).or can I change prop shaft seals without taking...
  4. S

    89 OMC 3 ltr coil question

    So I have a 89 OMC 3 ltr.switched to pertronix years ago with zero issues.now toasted 2 coils in 50 hrs of run time.( I always carry a spare now)any ideas??.can almost predict it because starts missing slightly at certain rpm and stalls at idle.
  5. S

    1989 3 ltr rebuild advice

    So I have a 89 21 ft renken fishing boat with the 3 ltr cobra.I have owned it for 18 ish years.Although they aren't well rated ,it's been a great boat.yhe original 3 ltr engine seem to be getting tired,yesterday after a hour of 3500 rpm something went bad,now stumbles after 2500 rpm.idles...
  6. S

    Did I find problem

    So 89 3 ltr was running great till 3000 rpm then starving for fuel.removed carb and found seat( needle seat) was loose 2 full turns.tightened it up and reassembled.havent test drove yet but pretty confident that was the issue.🤞🤞any ideas??
  7. S

    89 OMC 3ltr cobra water in drive

    First ride of the season noticed the drive was noisy.upon removal found water in the bellows.bellows was old and cracked.also noticed water in outdrive.( Milky).could water get forced into the drive because my bellows was full of water?I did a quick pressure test and saw no noticeable leaks.
  8. S

    89 3ltr cobra pertronix conversion question

    My 89 3ltr cobra has a pertronix igniter conversion.someone just gave me a flamethrower 2 coil. Will they work ok together or do I need a pertronix 2 module?
  9. S

    89 cobra 3 ltr miss.

    My boat kinda had me puzzled.2nd year it has done this.first time out boat starts right up ran fine for the first hour( really good actually).then started to miss again.full tune up.new cap and rotor.new fuel filters.I even drained the gas tank and put fresh gas.when I was draining the gas...
  10. S

    1992 15 hp running like crap

    1992 15 hp .won't idle,won't go full throttle.removed carb checked ,looks good,clean no wear,new plugs.Read about the top piece of carb cracking or warping.I can't see any cracks or warping ,Should I change that piece anyway.What else should I check?
  11. S

    Fuel mixture for trolling. merc 18xd 85

    Is there any benefit to running a leaner mixture for trolling.Ive heard of this ,but kinda questioned it?
  12. S

    85 merc 18xd

    Just aquired a 18xd.I already have a 90 15 2 stroke.This 18 is a brute of a motor for 3 more hp.Seem's to be in pretty good shape .Are these a good motor,Things I should watch.Thnaks.
  13. S

    1990 9.9 honda question

    Recently purchased 1990 9.9 honda.the oil pressure light that illuminates when running gets brighter as I accelerate,?seems dim at idle.Is this normal?
  14. S

    89 omc cobra shift issues

    Last year my cobra became very stiff to shift.Shift ok with engine off.When idling,if I trip shift interupter the engine does not stumble.Could this be causing the stiff shifting?Would it be the interupter or the shift assist module.it has pertronix pointless distibutor that would affect this...
  15. S

    evinrude 4.5 ser # c7198029 year?

    Was hoping someone could tell me the year.I guess around 85?Thanks
  16. S

    89 cobra shift issues

    Just replaced my lower shift cable but still have shifting issues.Seems like adjustment problem,When I adjust for forward reverse sometimes won't engage And visa,versa,Could a bad shift interupter switch cause this.When idling in neutral if I activate the switch there is no change in the...
  17. S

    85 alpha one rumble in outdrive

    Recently changed the gimbal bearing in a friends alpha one outdrive,seemed to be good for a couple weeks,She just called me to let me know that there is a rumble in the outdrive (she says same rumble that was there before I changed the bearing)She also said she hade a issue with alot of water...
  18. S

    omc 800 mechanical shift

    I have a 79 omc 800 mechanical shift.Won't go in to forward or reverse,Shifted fine when put away last fall,now nothing.Suspecting lower cable,should I look elsewhere?
  19. S

    omc 800 series won't shift

    omc 800 series,Ran good last fall put it in the water today,won't shift at all.There is a change in the tension on turning the prop when put in gear (not running),But the ball gears aren't moving,Any ideas would be great.
  20. S

    Fuel in the water

    !990 15 2 stroke runs good,idles good but there seems to be alot of fuel in the water.Fresh tank of fuel 50-1 give or take a hair.Like I said it seems to run good although if you go from full to an idle too quick it sometimes stalls,but will restart right away?
Top