Search results

  1. jim kinser

    wiring problem

    I have a 15hp mercury 2 stroke I changed power pack. Putting out spark but engine not starting. Could I have crossed coil wires?
  2. jim kinser

    shift shaft height

    2010 E150DSLISM anyone know the height for the shift shaft ?
  3. jim kinser

    ID number,

    I have a id plug for a model number I can't find info on. Model # E13907 serial number 9722B. Any help would be appreciated.
  4. jim kinser

    need to know

    1996 75hp mercury ser# 0G428139. I have been looking for a trim sender for this motor, it mounts on the right (starboard) side of the pin that goes to the upper part of the trim cylinder. This is a single cylinder tilt & trim. I have a part number that I think is the correct one ( 8M0074846 ).
  5. jim kinser

    90hp flywheel

    I have a 1997 90hp force ser#oe2219**** . Changed flywheel because old one decided to come apart. Now it will not run. Checked timing with light and found #1 cyl firing 120 degrees btdc, #2 cyl firing when #1 piston is tdc. #3 firing where it's supposed to. Changed trigger assy same firing...
  6. jim kinser

    yamaha water pressure

    Does any one know where the hose hook up to vz250tlr (2006) for a water pressure gauge goes , I got one that the hose was loose on the engine?
  7. jim kinser

    confused

    Serial number 0G692016 This is supposed to be a 1998 200hp mariner. But one source says it's a 225hp. Help appreciated. I need to order a cyl sleeve for it.
  8. jim kinser

    change over

    Thinking of changing engine from aq131a to a volvo B230f. One has distributer in block aq131a, the other has the distributer in the head B230f. Are there any difference's internal in then engine that will not work ?
  9. jim kinser

    pistons

    I would like to know what oversize pistons are available for aq131a engine and from whom they are available.
  10. jim kinser

    Mercury Gear case

    Does anyone have a timkin number for forward gear bearing 1996 115hp ?
  11. jim kinser

    fastrac honing

    Anyone have any luck honing a tilt cyl on a fastrac t/t ? I have one that is gaulded a little and makes the motor bounce when coming down.
  12. jim kinser

    gear sets

    Anyone know the difference between gears in these sets, 5004218 , 5004216 ? I've got a E225fplssc I need gears for.
  13. jim kinser

    plug size ??

    J115TLCNB 1982, tilt/trim #2 & #3 Anyone know what size these plugs are and what size allen wrench fits them ? I think they are metric but not sure. I'm going to perform pressure ckecks on and any info would be appreciated.
  14. jim kinser

    tilt/trim

    Anyone have a part number for a tilt/trim o-ring kit for 1980 Johnson 100hp.
  15. jim kinser

    prop

    I've got merc prop #48-76230-14. Anyone know what pitch it is ? I think it's a 14 pitch.
  16. jim kinser

    gears

    433618 brp part number,, anyone got a price ?? " GEAR, Reverse. On 1979-88 40, 48, 50-55 & 60 hp use part number #433570 On 1975-78 Models use part number 433618. "
  17. jim kinser

    VRO Vapor Seperator Photo

    This should help.
  18. jim kinser

    This may interest some

    A little help to someone. VRO and vapor seperator.
  19. jim kinser

    crank cross

    Will a crank from a '94 v4 work in a '89 block ?
  20. jim kinser

    ignition switch

    I need an ignition switch for a 2004 90hp 60 degree engine. Mod J90GLSRM. It's the one with bullet connectors on it.
Top