Search results

  1. B

    Volvo Ms3

    Any body out there have a procedure for replacing the sliding sleeve on a Ms3? Is it necessary to disassemble the drive to replace it or can it be done in the boat? Thanks, Gene
  2. B

    Fuel tanks 97 pursuit

    I have a 97 Pursuit with 2 tanks, one in front of the other. The boat is a 28 CC.The rear tank is leaking. There is not enough room to get the tank out without cutting out the floor between the tank cover & fish well. Has any one else had this problem? If so, what was your solution? Thanks
  3. B

    Volvo MS4

    I have a Volvo TAMD 41d coupled to an MS4 transmission. When the engine warms, the tranny will not go into forward. Anyone else have this problem before? Thanks
  4. B

    Tamd 41d

    Anyone know of a more reasonable place to buy VOLVO parts than VOLVO? That $200 "Made In Switzerland" sticker is getting expensive. I am looking for a sea water pump. Thanks, Gene
  5. B

    2005 mercury 25 hp tilt

    I have a 2005 mercury 25 hp on a 17' pontoon boat. No owners manual. Where is there a lever or tab to depress that will unlock the motor to tilt up? Two man job as it is. Thanks, Gene
  6. B

    Boat paint

    Does any one still use a straight marine enamel? How well does it hold up to abuse? I use my 25' boat almost everyday. It has to be cleaned every day resulting in water sitting on the deck for prolonged periods. Thanks, Gene
  7. B

    Sliding doors

    I am adding sliding doors to the pilothouse of my Kencraft. Any ideas on hardware distributors? Thanks, Gene
  8. B

    Stainless Steel oil pan

    I am looking for a Stainless Steel oil pan for a pre-1986 350 Chevrolet Thanks Gene
  9. B

    1984 Kencraft Buxton

    I am trying to locate parts. Anyone have any Info or pictures of an existing boat? Thanks Gene
  10. B

    Painting FRP

    I am about ready to paint a 25' Kencraft. The previous owner installed some fiberglass reinforced plastic in places then painted it. The paint peeled away in sheets. It is very difficult to sand because of the irregular surface. Is there a primer that will stick without sanding?<br /> Thanks,<br...
  11. B

    Exhaust

    I have a 1984 25' Kencraft with a 1994 TAMD 41 Volvo Diesel. The boat was used for shrimping & the owner converted the exhaust to a dry stack. I would like to convert it back to a wet exhaust. My situation is this: The exhaust elbow on the engine is about 1 foot above the water line. The floor...
  12. B

    Boat Information

    I have a 25' 1984 Kencraft. I suspect that this was once a fishing or lobster boat. I would like to restore her properly, but cannot seem to find any photos. Any-one else out there ever hear of a Kencraft?
  13. B

    VOLVO Inboard exhaust

    I have a 25' Kencraft with a TAMD41 diesel. I am converting this boat to use as a dive boat & would like to get the exhaust overhead instead of through the transom. Anyone here have any info on this procedure? I know shrimp boats do it.<br /> Thanks,<br /> Gene
  14. B

    Replacement windows

    Does anyone know of a salvage yard that will sell salvaged boat windows or windshields?<br /> Thanks<br /> Gene
  15. B

    Fuel Flow meters

    I have a 1979 OMC marinized 350 Chevy with a mechanical diaphragm fuel pump. I recently installed a Standard Horizon FF-41 fuel flow meter. When I run the engine, the meter runs backwards. For instance, at idle it shows a 25 gal. per hr. fuel flow. At 2600 rpm, it shows 3.4 gals. per hr.I called...
  16. B

    Plastic sliding window guides

    I have a 1979 AMF Slickcraft with sliding side windows. Does anyone know where I can find the plastic guides that the top & bottom slide on?<br /> Thanks
Top