Search results

  1. M

    carb ajusting question

    58 johnson sea horse 35hp. Do i have to ajust high speed first or can i ajust slow speed in a tank first?
  2. M

    fly wheel torgue specs

    1958 35 hp sea horse, what is the torgue specs for the fly wheel?
  3. M

    how do i set timing

    I have a 1958 sea horse 35hp, i hae been cha nging out coils, points, and condensers. How do get the timng set right, i noticed a mark on a brass plate under neath the coils and stuff but have no idea what to line it up with?
  4. M

    how do i test coils

    I removed fly wheel from my 58 model 35 hp sea horse and removed coils, one of the wires coming out of one coil was naked, not the ground the other one so i'm preety sure that on is bad if it isn't it will be in no time. The other coil is the one that i suspect is bad though, how can i test it?
  5. M

    still ain't running right

    !958 35 horse sea horse will crank runs rough it is spittin and cuttin out, has good spark, jumps a 1/4 inch gap, i have rebuilt carb. new plugs, blows my mind. Is it possible that it is still a carb probleme or is it possible it needs new coil(if so does it take 2) I cranked it for a minute...
  6. M

    Good or bad idea?

    I have a 1958 johnson 35 hp have rebuilt carb and still can't get it running right, i am now going to put a tune up kit and new coil in it waste of money or not?
  7. M

    gapping points

    How much do i gap points on my 58' 35hp sea horse?
  8. M

    1958 35hp sea horse please help very frustrated!!!

    Had this old motor gave to me, so far i have cleaned and rebuilt carb, replaced seals in lower unit, changed plugs, converted form dual line fuel system to single line fuel system(mukuni pump). Ajusted carb to starting out position as with directions from this forum, took it to the lake had a...
  9. M

    lower unit Question

    I have 1 1958 evinrude lower unit that i just replaced water pump, and all lower unit sills on. I put it in a bucket cranked nit ran good and was pumping water fine, so ishut it off and when i removed the bucket i notice a small wheep hole of some sort on one side of the lower unit. My question...
  10. M

    '57 johnson 35 hp seal???????

    Is there suppose to be a seal on top of the water pump housing for this model? There wasn't one when i took it off. Where do i get one if needed?
  11. M

    1958 35hp sea horse water pump question

    Is there suppose to be some type of rubber basket around bottom of the impeller housing. When i tour into mine ther wasn't just wondering if i should put some form-a-gasket around it when i reinstall it or not?
  12. M

    1958 35hp sea horse pulling lower unit

    How do i pull the lower unit on my 1958 35 seahorse?
  13. M

    impeller question

    I have a 1958 35hp johnson i oredered a impeller for it and it is alot thicker than the old one thats in it, almost twice as thick. I just wonder if they make two different impellers for the 58 one thick and one thin or if my motor is one of the earlier 58 models and takes the same impeller as...
  14. M

    1958 35 sea horse Is this possible?????

    Is it possible that some one has put a different model lower unit on my 1958 sea horse? The reason i am asking is because i ordered a new impeller, and the new on is twice the thickness as my old one. I don't no what to do, how am i suppose to find the right impeller? Some one please help!
  15. M

    1958 35 hp johnson

    How do i know if impeller needs replaced, can you tell by looking at it? Does anyone have any photos where they put a lower unit seals kit in one of these old motors?
  16. M

    mukuni fuel pump

    Will a mukuni single carb. pump supply the proper amount of fuel to a Rd-19-c 35 horse johonson?
  17. M

    1958 johnson 35 hp lower unit need help

    Been working on this old motor for a day or two, think i have finally got her to where she'll run, so like everyone has advised me was going to replace empeler. So i drain lower unit oil and find that it is full of water, got to looking and found that the prop shaft seal looks worn out. Is this...
  18. M

    1971 evinrude 50 hp

    I have a 1971 evinrude 50 hp, this motor runs fairly good, i think it just needs some tweaking done on the carbs. Mt question is what would be a fair price to sell it for?
  19. M

    1958 35hp sea horse carb ajusting

    Could some one walk me thru ajusting my carb, i'm not to good with this type of thing.
  20. M

    need help rd-19-c 1958 35hp sea horse johnson

    recently installed mukuni fuel pump, took it to the lake first time i pulled the cord boat cranked ran for a minute and died. So i pulled and pulledand it wouldn't hit a lick, screwed plugs out and pulled a few times to blow the gas out, screwed them bac in and it cranked ran for a minute and...
Top