Search results

  1. S

    1992 evinrude 150 EXEN vacuum line diagram

    this one has a tube that goes from the speed-o to the motor but it is not attached to anything, just sticking up in the air... Where would the tube attach?? I have looked but everything is so tight with all the wires and I don't know where to look...
  2. S

    1992 evinrude 150 EXEN vacuum line diagram

    10-4, I think I have it all figured out from here except where the speedometer tube goes. I thought it went to a pickup on the bottom stern of the hull but someone routed it to the inside of the engine compartment ?!?!?
  3. S

    1992 evinrude 150 EXEN vacuum line diagram

    what does it drain?? where does the tach tube connect to?
  4. S

    1992 evinrude 150 EXEN vacuum line diagram

    I have a couple vacuum lines that go no where, they just end and are not plugged. I have tried to find a vacuum diagram and have come up short. The manifold balance tube drains just hang down I assume, to drain. The picture shows a tee that comes from the bottom front of the block, hard to see...
  5. S

    1992 Evinrude 150 Oceanpro

    looks like some have the metal t-stat fitting inside a plastic housing and some without the housing
  6. S

    1992 Evinrude 150 Oceanpro

    that was my other option, the temp gun. should one head but warmer than the other?? and what is to hot a temp??
  7. S

    1992 Evinrude 150 Oceanpro

    I'm here in Charleston S.C. for a few months from Idaho doing some work so all my mechanikin tools are there. I really don't want to spend money on stuff I already have at home... I picked up the bloat knowing it needed some TLC so Break Out Another Thousand it is but I believe well worth...
  8. S

    1992 Evinrude 150 Oceanpro

    Port side from the top 1=92, 2=92, 3=94 Starboard side from the top 1=93, 2=98, 3=98 stayed the same even after I sprayed some lube in each cylinder and retested
  9. S

    1992 Evinrude 150 Oceanpro

    I really like this motor, from what I read they are pretty rugged, easy to work on and parts are available...
  10. S

    1992 Evinrude 150 Oceanpro

    I need to rent a comp. tester from the parts store. Been wanting to do this but been busy. I'll see if I can get one this afternoon..
  11. S

    1992 Evinrude 150 Oceanpro

    overheat alarm is not hooked up. I know it should chirp when the key is turned on which it does not. I have the service manual but the colors don't seem to match up. The buzzer has 2 wires going to one post and nothing on the other post so I need to find that wire. Who ever had it before did a...
  12. S

    1992 Evinrude 150 Oceanpro

    It does smoke till it warms up.. I'll put in the t-stats regardless and yes I'll get the SS ones for sure, thanks for the heads up on that... I was not sure if rough idle was adherent to these, it doesn't seem to be a problem just wasn't sure if it was normal or not.
  13. S

    1992 Evinrude 150 Oceanpro

    I recently purchased a 1986 20' Aquasport center console with the 1992 Evinrude 150 Oceanpro on it. I pulled the thermostat caps to see what the t-stats look like after being in salt water and there was no t-stats just a hole where they go. The VRO has been removed and everything bypassed...
  14. S

    Trim motor removal

    I need to remove my trim motor on a 93 200 hp yammie. Do I need to remove the engine to do this??? Also do not buy a Clymers manual unless you need foder for the fire.
  15. S

    Magic tilt trailer floats

    My trailer floats and it makes it quite difficult to load It is aluminum I beam dual axle with with wood skids any ideas how to solve the problem.
  16. S

    yamaha 93 200 hp trim motor

    My trim motor is sticking so I have to tap it to get to run,time for a cleaning. I ordered a Clymers ten minutes ago and won't get it till the week end. Is this book worth the money?? Anyway my ? is to drain the hyd fluid does the motor need to be up or down as I would like to get it apart for...
View older results
Top