Search results

  1. Lubak572

    DP-SM won't shift in to FWD or Rev.

    Is this what you are referring to?
  2. Lubak572

    DP-SM won't shift in to FWD or Rev.

    How hard is the coupler replacement job? I have split the drive before and changed water pipe and seals. Wondering if I can tackle myself. So your saying not to worry to much about a slight vacuum leak?
  3. Lubak572

    DP-SM won't shift in to FWD or Rev.

  4. Lubak572

    DP-SM won't shift in to FWD or Rev.

    Got both drives off and on stands. 1 didn't have reverse last year thought it was new cable I installed that was misaligned. When shifting by hands feels correct but doesn't link up input and output shafts at all. I hit something in water and bent prop when I lost all gears. Trying to...
  5. Lubak572

    ECM Swap ? Plug and play ???

    Mefi bob did mine. But it was for a 01 VP 5.7 GSIPEFS 6.2 upgrade.
  6. Lubak572

    Changing steering cable

    What is the best way to pull in a steering cable from helm side or engine side? 2001 four winns 298 Vista with twin vp 5.7 gsipefs .
  7. Lubak572

    5.7 GSIPEFS Timing??

    Got it running, turns out when I was installing motor my foot pushed in the retaining clip for the high pressure fuel pump when pushing that corner of motor back to clear deck. Started and runs fines, used rinda to put in base timing mode and locker it down. Now just have to change impellor...
  8. Lubak572

    5.7 GSIPEFS Timing??

    So what method to time it is used? I have seen both, using a rinda to put in base timing mode, on warmed up motor at 1000rpm or using the the timing shunt plugged i to the dizzy?
  9. Lubak572

    5.7 GSIPEFS Timing??

    Does this TBI motor have to be timed every time distributor is pulled out? Had heads reconditioned, I marked distributor when pulled. Put motor back in on #1 TDC can't get to run more than 30 seconds. It has to be close, loosened distributor bolt and have been turning dizzy a little. What a...
  10. Lubak572

    6.2 vortec head torque setting?

    Not to my knowledge, I put short bolts to 55 #, med 65, large 75 carefully in stages with my digital snap on torque wrench. Seems fine just probably overthinking it. Tired of messing with this motor/boat. Want it done and forget about it.
  11. Lubak572

    6.2 vortec head torque setting?

    I reused the stock ones supposed to be from new gm marine. I believe they are not torque to yield bolts. My question is if I over or under torqued them and should redo it with new bolts???
  12. Lubak572

    6.2 vortec head torque setting?

  13. Lubak572

    6.2 vortec head torque setting?

    I am putting heads on what was originally a 5.7 GSIPEFS motor that i converted to a 6.2 using a new 6.2 gm marine long block. Had to do a valve job on heads I am bolting them back on, service manual is at farm. I only have selected manual supposedly head torque is all at 22 foot pounds then 55...
  14. Lubak572

    DIY Head Porting?

    I'm running Hardin Marine exhaust and I upgraded my stock 5.7 to 6.2's.
  15. Lubak572

    DIY Head Porting?

    I have the heads off my 6.2 gm marine long block I recently installed in my boat due to a broken rocker arm stud. Is it worth it to port/polish them myself. I have all the tools and time.
  16. Lubak572

    Raw Water Pump Priming

    Could also be the raw water housing itself being worn. I will be replacing mine on one of my engines.
  17. Lubak572

    Lack of cooling water flow at idle and low rpm.

    Took in to shop. Mechanic thinks housing may be worn. Yes plastic nipple and water pipe on drive were changed when I had it apart. Will update when I hear what problem was.
  18. Lubak572

    Lack of cooling water flow at idle and low rpm.

    No
  19. Lubak572

    Volvo penta 5.0 knocking sound

    Following
  20. Lubak572

    2001 volvo penta 5.7 GSIPEFS long blocks value??

    I have 2 long blocks. I lost a motor to water ingestion, so I replaced both with 6.2 long blocks. What are these worth? Had 330 hours one ran fine, other had water, still turns over. I may sell or rebuild. Both raw water cooled.
Top