The iboats forum moderators are excited to announce that at this time it appears the iboats forums posting pictures function is working once again. Though we cannot promise for how long, we're hoping for indefinitely.
Can anyone tell me where to find new needle valve and seats for mercury wme carbs for a 1994 75hp. ser. # OD269743. I have checked I-Boats and all they have are gasket sets no needle valve and seats in the kits. Thanks for any help.
Hi, I have a 1994 mercury 75hp. I have installed a new temp gauge with sending unit. problem is it's not working. ohms at sending unit is within specs. 16g wire running from sending unit to gauge and hooked up to the "s" terminal. 16g wire hooked up to the purple wire from ign switch and hooked...
can anyone tell me where to get a "z" bracket for a temp sending unit to go on a mercury 75 hp 1994. The head bolts are raised so the flat bracket i got with it will not work.thanks
hi, I have a 94 mercury 75hp that has been running about 5psi water pressure at idle. at 3500 rpm i get about 10 psi, If I raise the rpm's above 3500 rpm's my water pressure drops to around 4psi until i lower the rpm's back to 3500 or less and then jumps back to 10 psi. this has just started as...
I am planning to get boat towing and was wondering what you guys thought of the two choices. Who is better or are they both about the same? Thanks for your comments and or views.
hi, Does anyone know how to get the prv rubber seal out of a 150hp yamaha that has been dropped inside the motor. Was replacing the rubber seal when it dropped into the motor. Thanks for any help.
hi, I have a 1995 yamaha 150hp and it starts overheating at or above 1400 rpm. Have replaced water pump, thermostats, and prv. at idle runs great, no problem with starting. but as soon as it gets at or above 1400rpm ,over heat alarm goes off. Can anyone help? Thanks
hi, have 1995 yamaha 150hp salt water edition outboard. p.o. never flushed motor after running in salt water for about 2 years.then motor sat for about a year. problem is motor is over heating. pulled and replaced thremostats. both were plugged with salt. now motor is still over heating and...
I have a 1994 75hp mercury outboard. my problem is the ignition switch needed to be replaced. p.o. changed the wiring and now i'm looking for a wiring diagram in order to replace this switch. any help?? the ignition switch is mounted in a center console. quicksilver controls mounted next to it...
I am trying to hook up a duel battery system on my boat. I have a 1987 70 hp evinrude outboard. I have a battery selector switch and it says to hook a wire to the alternator but I don't have a wire diagram for this engine, any help would be appreciated. the battery selector is an attwood #14230
I'm trying to find the right part numbers to replace my thermostat. Just bought this motor and it has no thermostat in it at this time. the p.o. removed it and told me he never uses a thermostat in fla. because it's always warm here. I was told running without one is almost as bad as running an...
Just got this engine and at idle runs great.took to the water left the dock at low speed and was running fine, ran good until I hit w.o.t., ran for about 2 min and lost power. idled back to dock, when got home found fuel coming out of the front of the carbs. rebuilt carbs and still no power...
I have a 1983 Johnson 90hp model # J90TLCTE my problem is the motor was running great. started right up at the dock, idled great, left the dock and was running about half speed when heard a rattling noise. I kicked it down to idle and it idled for about 30 seconds and quit running.I tried to...
I am looking at a small pull start mercury out board for use as a kicker motor but cannot find year or hp of this motor. ser # is B325324. Any help on size and year thanks.
can anyone tell me where to locate a voltage regulator for a 1983 johnson 90hp with trim and tilt model # J90TLCTE. I have found the rectifier here at I-Boats but no regulator.would be thankful for any help