Search results

  1. 4

    check this out !!!

    tugboat
  2. 4

    lower unit lube for 64 evinrude

    hello all, i have a 64 60 hp evinrude i need to find lower unit oil to replace type c [hard to find] i have been to walmart and not sure what is compatable to type c , any suggjestions?? many thanks !!
  3. 4

    oil filters

    its time to change the oil in the ol pickup again and was about to go to the store to pick up oil and filter , rembering a topic that was brought up here,bout fram oil filters and there credibility ,so what does everyone suggest ?????
  4. 4

    minn kota parts

    hello all , i managed to break what i think is the t bar on my trolling motor and cant seem to find a site that carrys this specific part anybody know were i can order this part thanks
  5. 4

    minn kota parts

    hello, does anyone know were you can order parts online for minn kota trolling motors ???
  6. 4

    check out this link !!!

    found this browsing one night tugboat
  7. 4

    largemouth

    last try at posting pics hope it works this time , anyway 5lb 22 inch largemouthfishing works
  8. 4

    largemouth

    here is a pic of the largemouth i caught hope the pic works<br /> 5lbs 22 inchesFISHING WORKS HOMEPAGE
  9. 4

    reed valves

    hello ,i have a 1964 evinrude 60 hp model #60453s serial # eo1852 am looking for reed valves for it , have looked at the boysen sight but they dont seem to have any application listings , are there other makers of performance reed vales ??and if so please list websites or other suggestions...
  10. 4

    water pump

    hello all, am looking for a water pump kit for a 64 evinrude sport 4 60 hp model number 60453s , serial number EO1852 , does anybody know the part number and were i might find one
  11. 4

    stumped can someone help ???

    hello all ,1964 evinrude 60 hp when i open the motor up at wot it will sit at about 2400 rpm and stays there for about 15 to 20 seconds, runing ok no apparent miss, sounds good , after the 15 to 20 seconds it opens up to about 4000 rpm , i cant figure out why it sits so long at 2400 and will...
  12. 4

    if interested , have pics of my almost finished boat floor.

    my boat floor is almost finished am hoping that these pics work , anyway replaced stringers floor and carpet, not a real fun job , glad the worst is over, thanks to all for all the post i have read about redoing floors, a great help !!! yahoo
  13. 4

    place where i can order parts from ??

    hello all , am looking for places on-line to order parts for a old evinrude, 1964 60 hp v-4 mag style, i dont have a dealer anywere close to wear i live , i do use the mastertec site but looking for other options , also anyone know were i can get a shear pin for the prop??? thanks!!!!
  14. 4

    engine part numbers

    hello all , i have a old 64 60hp v-4 evinrude , my question is when i am looking for parts such as carbkits , impeller and so forth i do not know the part number , my engine book does not list the part numbers , so when i go to a place such as i boats to look for parts i mostly have to take a...
  15. 4

    engine part numbers

    hello all , i have a old 64 60hp v-4 evinrude , my question is when i am looking for parts such as carbkits , impeller and so forth i do not know the part number , my engine book does not list the part numbers , so when i go to a place such as i boats to look for parts i mostly have to take a...
  16. 4

    new floor pics

    well i have just about finished my floor project, imagestation just wanted to show it off , next project new vinyl
  17. 4

    pics

    well this is my third try at posting pics if it dosent work this time i give up lol ,anyway redone stringers and floor and wanted to show off the finished floor , next to be replaced is all the vinyl thanks to all for the post ive been reading , a great help !!! imagestation
  18. 4

    hope these pics work

    well i tried to get the pics on it did not work so i will try this
  19. 4

    new floor almost finished

    <br />hello all , i have pretty well finished my floor project and i do hope the pics work , have never done this before , wanted to thank you all for all the post i have read , could not have done it withought the reading and knowledge especially jason j for his posts and pics, redone stringers...
  20. 4

    how to post pics

    how does a person go about putting pics on this site???<br /><br /> thanks
Top