Search results

  1. K

    1986 Mercury 9.8 110 outboard

    If the pin was missed would that keep it from firing at all even with premix sprayed into the carb?
  2. K

    1986 Mercury 9.8 110 outboard

    If I did miss the pin, I should be able to get it back in without pulling pistons all the way out? I don't want to break another ring as I say, not able to find more.
  3. K

    1986 Mercury 9.8 110 outboard

    I will check into them thanks. I tried some in Calgary and they all said you can’t get them anymore from Mercury.
  4. K

    1986 Mercury 9.8 110 outboard

    I am in Alberta Canada
  5. K

    1986 Mercury 9.8 110 outboard

    would you happen to know where I could find more piston rings for this motor? Parts people I have contacted say they are no longer available. Also, what is the purpose of that pin and would it make it not start?
  6. K

    1986 Mercury 9.8 110 outboard

    I did put a very thin coat on. And if this pin wasn’t lined up correctly, no hope of running then?
  7. K

    1986 Mercury 9.8 110 outboard

    Can you explain as to what pin you’re talking about?
  8. K

    1986 Mercury 9.8 110 outboard

    I sealed it with motoseal by Pernetex I believe it’s called and the reeds are in center bearing of crank, seemed to go in right.
  9. K

    1986 Mercury 9.8 110 outboard

    After reading over these posts I realized that didn't explain myself very well and I'm sorry. my problem originated when I lost compression and couldn't even pull start at all so what I did was, took the powerhead apart, went thru it checking reeds, bearings and such. The problem I believe was...
  10. K

    1986 Mercury 9.8 110 outboard

    I have tried what you said to do, swapped the plug leads and fuel in the plug holes and still nothing happens when I pull start. I am using a plug tester and it does jump 3/8" on both. Do you think maybe the coils could be bad?
  11. K

    1986 Mercury 9.8 110 outboard

    no the flywheel key is ok.
  12. K

    1986 Mercury 9.8 110 outboard

    I have good gap on spark plugs, put fuel down plug holes and nothing happens, doesn't even fire at all. Anything else that I could be missing here?
  13. K

    1986 Mercury 9.8 110 outboard

    Thanks I will let you know how I make out.
  14. K

    1986 Mercury 9.8 110 outboard

    I might have the coil wires on wrong. I will figure that out and check
  15. K

    1980 110(9.8) hp Mercury outboard

    Thank you
  16. K

    1986 Mercury 9.8 110 outboard

    I have tried that and nothing. The wires that go on coils I’m not sure about. I’m wondering if the blue/ white stripe wire is positive or negative that goes on the coil.
  17. K

    1986 Mercury 9.8 110 outboard

    I got the motor all put back together, compression is just under 100 on both cylinder. have checked spark which is good and sprayed a little pre mix into carb throat, still won't even try to start. Any ideas?
  18. K

    1986 Mercury 9.8 110 outboard

    I got this motor all put back together and still have no wet spark plugs. I've checked the spark and its good but the motor still won't even try to start. I have sprayed a little premix into the carb throat as well, any I deas to what I'm doing wrong?
  19. K

    1980 110(9.8) hp Mercury outboard

    which wire is positive? white stripe or solid colour?
  20. K

    1980 110(9.8) hp Mercury outboard

    I was wondering if someone could help me please. I have a 110 HP mercury outboard and I can't find a manual for it. I need to know on the two coils I have a green/white stripe wire and a blue/ whit stripe wire, are those positive or negative wires? the other two are green and blue. Thanks in...
Top