Search results

  1. ratdude747

    No water coming out of the exhaust on muffs

    I'm pretty sure I had one donut on the water tube, and another on the input shaft itself. The shifter (at least on my MC-1) was outside the outdrive casing, using a slotted slip joint that had to be lined up for the lower unit to fully seat on the upper (drove me nuts the first time, I tell you).
  2. ratdude747

    No water coming out of the exhaust on muffs

    Nope. You want the engine up to operating temp. Oil thins with heat; what oil to use is partially based on what temp the crankcase will be operating at, hence old engines like my 1976 Mercruiser 888 (302) calling out three different weights depending on water temps (as back then, good...
  3. ratdude747

    Modifying a 1975 Trail-R-Craft

    Parts have been purchased. Going with TruRyde brakes, but the "pro" kit with Timken bearings and seals. Also using new chrome bearing buddies as the existing clear plastic loadrite ones I have doubts about holding up on a brake hub. Finally, I am trying a solar breakaway battery system as the...
  4. ratdude747

    Modifying a 1975 Trail-R-Craft

    Other trailer sold... so I now have $400 to go to the brake and ladder fund. Will focus on the former since it's a bit of a safety item (I.E. not replacing wheel seals in hubs that I was going to swap for drums anyway)...
  5. ratdude747

    Cross country trailering advice/tips

    Agreed. With tapered roller bearings, always go loose rather than tight. Also why regular nuts with sheet metal retainers are better than castle nuts for tapered roller spindles: These are available at most auto part stores. But the shorter nuts... I don't know. Never tried the swap. The...
  6. ratdude747

    Modifying a 1975 Trail-R-Craft

    Came home from lunch to find my wiring being inspected: The inspector says I'm nuts. Well. He has a point... Ok, you can stop booing now! Anyway, I wasn't happy with the section by the jack mount, so I redid it: I'll probably replace the spacers as white nylon and UV don't mix. But it's...
  7. ratdude747

    Cross country trailering advice/tips

    I have plastic "off brand" bearing buddies on my trailer. Installed by the previous owner a long time ago. Top them off every season, no issues. But when I add drum brakes, I'll probably swap to name brand metal ones since I don't think the plastic will agree with brake heat.
  8. ratdude747

    Modifying a 1975 Trail-R-Craft

    Tied up the wiring better: (Also got the reflectors installed... easy and cheap fix) The main cable will be locked in place with a zip tie or two once I have the truck hooked up to it next so I can get the length dialed in. A lot of this intentionally "loose" due to all the changes yet to...
  9. ratdude747

    Modifying a 1975 Trail-R-Craft

    Technically my front marker light swap last year was illegal as those lights don't have a reflector element (I was looking for lights with dedicated ground wires, oblivious to the lack of a reflector. Not the end of the world... just use separate reflectors, right? That'll also cover up the ugly...
  10. ratdude747

    Modifying a 1975 Trail-R-Craft

    7-way cable/junction boxes were on super sale the other day, so I ordered one... and it came in. So, I decided to install it: Seeing this (and how terrible my old install of the the marker lights was got me thinking... could the lights be part of the box. Well, a couple of 5/8" holes with a...
  11. ratdude747

    No water coming out of the exhaust on muffs

    I had to drill a hole in each plastic intake plate on my outdrive for the wire to pass through (Mercruiser MC-1). The intake holes themselves don't work due to internal interference. But there is clearance if one drills holes in the plastic , which is what one has to do. Totally worth it...
  12. ratdude747

    No water coming out of the exhaust on muffs

    Hence why I made the switch. They're not terribly expensive and seal a lot better. Sure, having to drill holes kinda stinks, but it's not rocket surgery.
  13. ratdude747

    No water coming out of the exhaust on muffs

    What kind of muffs do you have? On my mercruiser (1976 888/mc-1) I ended up having to use the bravo-style mercruiser muffs (looks like a set of crash cymbals). I had no luck with an "earmuffs" style muff set and bbq'd a new impeller partially as a result of such. You will have to drill a hole in...
  14. ratdude747

    Modifying a 1975 Trail-R-Craft

    Made it home... and while it was approaching midnight and drizzling... I had to install it! (Well, mostly, see below for the caveat). Originally, I was just going to mock it up. I already had a loose U bolt (that I discovered and didn't bother tightening up) and did this to confirm all the...
  15. ratdude747

    Modifying a 1975 Trail-R-Craft

    The last post is incomplete. I had my best friend show up (the one whose aunt gave me the boat!) and had to finish the post... and in doing so, I forgot a picture. It seems that they did give a turnbuckle/chain point on the winch mount: I'm wondering if this is to allow a chain...
  16. ratdude747

    Modifying a 1975 Trail-R-Craft

    Did some work in my Father-in-law's shop this morning (they live on the way home in Lafayette, IN, so we turned this adventure into a visit with them)... pulled the rusty winch and mangled U-bolt off. I then moved the winch mount to the 23.675" measurement I previously measured: Now, to...
  17. ratdude747

    Modifying a 1975 Trail-R-Craft

    Winch stand fetched. Unit is in excellent structural condition (minus the winch, but I'm replacing that). Rollers are genuine stolz and in great shape too... A long drive, yes. But so far a good road trip other than Chicago traffic...
  18. ratdude747

    Harbor freight jack.

    I have a 3 ton (or is it 2.5 ton?) pittsburgh low-profile... I've owned it for 11 years, still works great other than loosing the screw that holds the handles together. Heavy, but functional... and the release valve is very smooth (U-joint, not bevel gears). Great value for the money back then...
  19. ratdude747

    Modifying a 1975 Trail-R-Craft

    In no order: The original transom straps (a wire cam lock style) were very confusing to use (we almost gave up on using them as we couldn't remember how they were laced!). Yes, they had no ratchet to rust up, but swapping them for the boat buckles I have installed currently was one of the first...
  20. ratdude747

    Modifying a 1975 Trail-R-Craft

    One more possible issue with brakes I just realized: are the 4 u-bolts holding the axle/spring assembly to the frame able to take the braking load? They're the same diameter as as the two that hold the winch stand, but they (obviously don't have bunk friction helping reduce the load. Not...
Top