Search results

  1. S

    77s model 15hp evinrude

    It starts rite up, runs great for a few minutes, then goes dead. Then it will not start at all. Plugs fire 1/2 inch. after cooling or waiting a while, it will start instantly. runs goes dead again. So it always has fire and fuel. I don't know???? Any ideas or answers greatly appreciated...
  2. S

    mercury 500 50hp ignition connection

    ignition wire completely gone.so i have replaced the wire, but cannot find where it connects on the motor. please help thanks i think it is around 1978 model
  3. S

    1995 50hp evinrude shift rod assembly

    I am putting lower unit back together. Everythings good until getting shift rod linkage to line up in the cradle.Spent 2 days tryin, there has got to be a way, I just do not know how! Please help
  4. S

    1989 30hp yamaha leaking lower unit oil

    This motor is leaking oil from what i thought was a vent hole.The hole is located beside the oil level hole. When i fill the unit, oil comes out immediately . I guess it must be a seal? thanks guys
  5. S

    2012 mercury 50hp 4 stroke

    starts quick, idles perfect, but will not take gas and go. any ideas or suggestions thanks guys.
  6. S

    evinrude serial # site

    is there a site that i can use to identify year model. i do not have model # iboats only has model #s thanks
  7. S

    1994 50 hp evinrude replace pinion bearing

    I have removed the old bearing. Asking the experts before i mess up how to install the new bearing. Thanks guys
  8. S

    4hp johnson running hot

    I have replaced with complete water pump replacement, Still running hot. Removed cylinder head, water coming from all holes on bottom cyl. none from top cylinder. Any ideas? thanks guys
  9. S

    1975 mercury 500 50hp tilt quit

    It has been working fine, until today. The pump is working, but not moving, so I put more fluid still nothing. The fluid is not leaking out anywhere. I can physically lift the motor with no problem.any ideas?? Thanks
  10. S

    1994 50hp evinrude pinion bearing remove and replace

    i have to replace my pinion bearing. it looks difficult, i am having a hard time just getting the old one out.Any advice or suggestions will be greatly appreciated.
  11. S

    looking for cdi mercury

    i am looking for cdi for mercury 500 1975 50hp #333-3213a3 if anyone has a suggestion thank you
  12. S

    1988 yamaha 70 hp identify

    for 3 days i have been trying to get a part number for the last part connected to the shift rod in the lower unit . does any have a diagram,or can help in any way.last part connected to the shift rod i need a part # thanksguys,sam
  13. S

    evinrude wire color code

    where can i find a wire color code? thanks guys
  14. S

    1990 evinrude 50

    this motor starts easy and seems to run ok at speed. At idol it runs rough ,coughs spits a little out of the low speed idle, Carbs have been cleaned. Any suggestions greatly. Thanks guys
  15. S

    1990 50hp stator no fire evinrude

    so i got another stator and still no fire. I have a good battery, and spinning over with plugs out fast, no fire at all. any ideas suggestions greatly appreciated. thanks guys
  16. S

    link and sync carbs 1988 70hp evinrude

    is there any way to sync carbs without proper tool?? thanks guys
  17. S

    24volt 82lb thrust touring edition

    I just got this on a boat I purchased, does not work. I opened it up and found shorted wires. there is a relay and a electric board that looks fine. I do not know what brand this motor is.Any ideas or suggestion greatly appreciated. thanks
  18. S

    50hp evinrude little spark

    The spark on the plugs I can hardly see tiny. battery , starter working fine. I am spinning with the plugs out. Plenty fast to start. any advice to what to try? thanks
  19. S

    1988 50hp evinrude NO spark

    It has been running ok, put it in the water no spark at all. I disconnected kill wires. no good.should the coils have fire when the ignition is on? Any ideas or suggestion greatly appreciated. How to trouble shoot?? Thanks guys
  20. S

    mercury bottom carb blowing out

    1995 40hp 4cyl mercury running rough bottom carb is blowing out while motor is running I can cover carb with my hand and makes no difference in running. would it be compression blowing out? any suggestion or idea greatly appreciated. thanks
Top