Search results

  1. P

    Installing Boat drain Plug Question ?????

    My drain plug was leaking so I was trying to remove the 3 drain plug screws on my 89 bayliner and did the fun thing of breaking the screws off when I torqued them to hard to remove. I drilled them out and have to install a new one, one of the brass looking ones with the 3 screws, I'm sure you...
  2. P

    Keeping your boat interior nice, what do you use?

    Just wanted some opinions on what you think is the best stuff to use to keep your interior of your boat in good shape. I'm talking about the vinyl seats & side rails. I picked up an 89 bayliner with next to mint original interior and want to keep it looking that way. Some say leather care...
  3. P

    What spark plugs to use?? 1990 120hp Force

    The book shown UL-18V US and QL-76V Canadian. I have a 4 cyl. 1990 120hp force motor, 1201X90B. I have searched these numbers and find nothing. Are they called by another number now? thanks for any help.
  4. P

    Fuel/Water Separator Question?

    Bought this Attwood fuel/water separator, might be a silly question but does it also filter the gas just as a regular fuel filter would? thanks for any info.
  5. P

    Skeg is Bent, try to straighten?

    the skeg on my 90 120hp force is bent, you know it looks a little like Orka the killer whale's fin. I would say the tip is bent about 3/4" out from being perfectly straight. Should I try to straighten it? is this that much of an issue? thanks for any advise.
  6. P

    Electric choke not working? 1990 120hp Force

    Green wire is routed and hooked up correctly but when I push the key plunger no choke, do you have to jump another wire to the choke? it just has the yellow wire attached that look like it runs to the neutral safety switch area and under the battery hookup bolts. Starter engages fine when the...
  7. P

    1990 Force 120hp control cable end to short??

    I was hooking up the control cables and the distance between the slot in the cable end to where it clips to the motor is about 3/4 of an inch to short even turned out almost all of the way, the other cable is fine. In the swivel clamp with the 1 screw I have it tightened up on the rear of the...
  8. P

    Hooking up 120hp Force electrical diagram??

    hello, just wondering if anyone might have a wiring diagram for this motor? 1990 Force 120hp 1201X90B. Going to try and hook up the wiring harness to the motor, the boat had an OMC motor on it so now I just have the motor mounted and the US marine controller. I have the main harness and then the...
  9. P

    1990 120hp Force Parts book, manual? ??'s

    Does anyone know where I can get a parts book for a long shaft 1990 120hp Force motor? the model is 1201X90B. I am also looking for a book that would show the US Marine controller wireing hookup to the motor. I will probably end up getting a clymer book if all else fails. It would be nice to...
  10. P

    What is the weight of 1990 Force 120hp 1201X90B?

    Can you tell me the weight of this motor? 1990 Force 120hp long shaft 1201X90B. thank you
  11. P

    Force Trim n Tilt Pump not activating

    On this Force 1990 120hp 1201X90B the pump seemed to work fine both ways when I tested at the relay, I had to replace a broken steel hydrolic hose. I pulled the top off to make sure all was clean and everything did look real clean. After I put it together it acts like it is not getting power...
  12. P

    1990 Force 120hp Tilt n Trim line broken???

    I have a 1990 force 120hp 1201X90B. On the tilt n trim unit the steel line that attaches underneath the pump then is routed through the nickel size cut out at the front of the unit then connects to the lift cylinder is broken. Where can you find these parts? What is the part number? I have been...
View older results
Top