Search results

  1. Don S

    Remote drive oil tank- MC1

    Re: Remote drive oil tank- MC1 Mercruiser has had a drive lube reservoir as an option since the early 80's.
  2. Don S

    1988 Bayliner 2.3L Ford - Trim Will Not Work

    Re: 1988 Bayliner 2.3L Ford - Trim Will Not Work Since it's clicking, I will assume the clicking is coming from the solenoids on the engine. Below is the wiring diagram. Make sure the 50A fuse is good and you have power on the up and down solenoids on the red/purple wires. If that checks out...
  3. Don S

    Where can you purchase a neutral button?

    Re: Where can you purchase a neutral button? Item 45 in the picture below is what the button pushes on.
  4. Don S

    old bayliner Santiago new to me

    Re: old bayliner Santiago new to me I agree, I remember it on my engine on a previous boat as being on the starboard side, actually looked through some old photos of my engine and sure enough, port side.
  5. Don S

    change ampmeter to voltmeter

    Re: change ampmeter to voltmeter This may help.
  6. Don S

    I need help with electrical system(with pictures)

    Re: I need help with electrical system(with pictures) He's done exactly that, and I made a wiring diagram for him for a complete rewire, he just never came back to update any of his threads after he got the diagrams. He gave me a list of what he wanted, and this is what I made for him.
  7. Don S

    Anyone watching the truck race

    :eek: :eek: :eek: Yellow at less than ten to go, and these guys have raced like it's the last lap since lap one.
  8. Don S

    Need Help on Hose Identification

    Re: Need Help on Hose Identification Scroll down the list and look at the "Standard Cooling System" section. That will show you the raw water system. I can't tell from your picture what the hose goes to on either end. EDIT: After looking at your picture again, it looks like item 17 is the...
  9. Don S

    Closed cooling for Mercruiser 5.0 2013 with cats

    Re: Closed cooling for Mercruiser 5.0 2013 with cats That kit price is for the cooling kit only. Nothing about the ECM or the hose kit. Here is the kit itself.
  10. Don S

    Smartcraft question

    Re: Smartcraft question Your PCM and wiring harness is set up for it, but you will need the CAN harness and other items shown in the instruction sheet Fun Times posted. Page 9 of those instructions give you the PN. Make absolutely sure to put the term. resistors as shown, and get caps for all...
  11. Don S

    Closed cooling for Mercruiser 5.0 2013 with cats

    Re: Closed cooling for Mercruiser 5.0 2013 with cats I don't understand the one piece statement, have a look at the parts diagram for your engine.
  12. Don S

    How to repair a rubber exhaust bellows

    Re: How to repair a rubber exhaust bellows Obviously people replying have no clue what the exhaust bellows on an L-drive is. Item 7 in the picture below, PN F695130-3.
  13. Don S

    Mercruiser in a Volvo Penta?

    Re: Mercruiser in a Volvo Penta? Here is a .pdf files of what may work, I don't do Europe sites.
  14. Don S

    Where can you purchase a neutral button?

    Re: Where can you purchase a neutral button? Then you best post a picture of your control so we know what you have. Because that is the only one I know of with a square button. Here it is together.
  15. Don S

    Primary Shaft service info needed. AQ-280 out drive/ AQ-260 motor

    Re: Primary Shaft service info needed. AQ-280 out drive/ AQ-260 motor To pull the engine on your setup, just remove the upper gear box on the drive. No need to remove the complete drive. Once you have the upper gear box off, remove the 6 bolts holding the clamp ring in and remove the clamp...
  16. Don S

    Where can you purchase a neutral button?

    Re: Where can you purchase a neutral button? Any Mercruiser dealer can order the parts for you, or check with your local Merc dealer. They only cost less than $2. The part number is 88149 if this is your control and the item is #20.
  17. Don S

    Mercruiser 4.3 - small fuel leak near fuel/water separator

    Re: Mercruiser 4.3 - small fuel leak near fuel/water separator You don't use thread sealer on flared fittings, you make sure there are no cracks, and it's clean and put it back together. That sealer would be used on the fittings pipe threads where it screws into the filter housing.
  18. Don S

    Dual Battery Setup

    Re: Dual Battery Setup I do have one question, why the wire between the engine and house fuse panels?
  19. Don S

    breaker point to electronic ignition conversion now no spark. Turns over fine.

    Re: breaker point to electronic ignition conversion now no spark. Turns over fine. Here is a wiring diagram for a 3.0L Merc with EST, there is no green/white wire in the harness itself. There is a green/white wire coming off the distributor and going to the shift interrupt switch. Take...
  20. Don S

    Wiring diagram for 2002 mercury 90 hp

    Re: Wiring diagram for 2002 mercury 90 hp Here ya go.
Top