Search results

  1. J

    Johnson HD 25

    Hi, I have a Johnson HD 25 that I am bringing back from the brink. I'll need gaskets, carb kit, starter spring, etc... Two questions: 1 Serial 72491, what year is this one? 2 Where can I find parts? Thanks, J
  2. J

    Johnson HD 25

    Hi. I have what I think is a Johnson HD 25. The engine paint is green and the model number is cast into the engine block. Paint is humble and decals are gone. Where can I find an exploded view parts list and who carries parts for this thing? I'll need typical stuff like carb rebuild kit and...
  3. J

    Mariner 115 Alarm

    Hi, I've got a mariner 115 which was run low on oil. The alarm sounded. Engine was shut down. Now, when the ignition key is turned the alarm goes off and will not stop. The engine will run with the alarm going off. Is this steady beeeeeeep the over-heat signal or oil? Thanks, J
  4. J

    Mercury 0G160953 Not Starting

    Hi, guys, Long time...always good to be here. I was called by a friend to help reassemble the gear shift control lever at the helm. Engine serial number 0G160953. Whoever took it apart lost their way. I reassembled the unit. Gear shifting and throttle control are functional; verified. Now...
  5. J

    Steam from Tell Tale

    Was just out trying to help a Mariner that won;t stay running. Probably bad fuel and something 's stuck in the jets, now. Anyway, while I'm watching this thing, I see steam coming out along with a good steady stream of water. I put my hand in the stream and, ZOWIE, that water is HOT. Is there...
  6. J

    Dropping the lower unit on a 2004 T50

    I need to replace the impeller in a T50. So, 3 questions. 1 Where do I disconnect the shifter linkage? 2 Are there any other surprises that need to be undone before the unit drops? 3 Where can I find a good exploded view of the BOM? Thanks. J
  7. J

    Mercury 40, 2 cylinder, Canadian Engine

    Does water flow through this fuel pump? Hose to "tell tale"? Yikes! J
  8. J

    Merc 18 5995557 Main Jet Size or Carburetor Float: You Be the Judge

    My Merc 18 is running rich at high speed, too much fuel. Clears itself at WOT and then repeats; gets to choking up a little, then clears out and screams, repeat. Main jet measures 0.002 above stock @ 0.054. Is main jet worn out from use, and letting too much fuel in? So, try to find a main jet...
  9. J

    Muncie Gear Neptune 10A2

    I'm trying to save a Neptune 10A2, c. 1940. The piston is frozen in the cylinder. I believe from neglect and rust and not from scoring. The connecting rod and crank are in good shape. I have the cylinder flooded with PB Blaster, soaking. Is there anything else I can try to loosen the piston...
  10. J

    1976 Evinrude 55 Won't Split

    Hi, I have a 1976 Evinrude 55, 55673E, that needs a new upper rubber mount. I'm trying to pull the power head, but, it won't split at the exhaust housing. Carburetors and starter are off. The electronics are still attached. I have removed (8) bolts around the exhaust housing, two adapter to...
  11. J

    Evinrude 55673E Power Head Shake

    Hi. I have a 1976 55 hp, 55673E. The power head shakes and can be pushed back and forth just as it sits. It should definitely not be used like this. I'm looking for ideas before I tear into it. The drive shaft, exhaust housing, shift linkage all seem in place and tight, but there's a lot of...
  12. J

    What Year is JW-16?

    Hi, team. I am bringing back a cute little Johnson 3. It's a JW-16. Now, I believe a JW-16 is a 1960, but, the parts lists I am looking at show a 1960 as a JW-13 and a 1961 as a JW-17. So, what year is the JW-16? Thanks, J p.s., and in the absence of a JW-16 parts list, are the JW-17 parts the...
  13. J

    JW-16 Exhaust Route

    I have a JW-16 that is just plain sweet. It's tight and runs well, but needs a good carb cleaning. I do not see water coming out anywhere so I am wondering if I should see water spray from the down tube. Thanks, J
  14. J

    Merc 18 5995557 Shearing Drive Keys

    I have an 18 Merc, 5995557, that I just put new bearings (crank and drive shaft) and seals. Started it up in a barrel. Much quieter, lot less rattling and no more squeaking. Shut it down and wouldn't restart. Found the drive key sheared right in half. Installed another one and same thing...
  15. J

    1974 Correct Craft Mustang 17, 302 v-8, Holley 4bbl

    I've got a 1974 Correct Craft Mustang 17 with a 302 V-8 and Holley 4bbl. Is there a hook in the iBoats forum for Holley questions? Thanks, J
  16. J

    Bearing Sleeve 23-85092 from Merc 18 5995557

    Hi, I am ready to reassemble the drive shaft bearing of the lower unit. I see in the parts list a bearing sleeve PN 23-85092. I did not get one of these out when I ground out the bearing. Am I missing something? Thanks, J
  17. J

    Merc 18 5995557 Lower Unit Rebuild

    I am bringing back an 18 hp Merc, 5995557. It's had a hard life but still runs like a beast. I've been through the power head and am now doing the lower unit. The unit needs new seals, (2) upper and (1) lower. The old upper seals gave me a much harder time than expected. I got them out by...
  18. J

    Shocking Evinrude E2RCOC

    I have a 1985 E2RCOC that I have gone through but I'm still not able to find the electrical leak. I am getting zapped when I move the armature plate. One of the next steps is to replace the magneto and spark plug wire. Somehow the armature plate is getting electrically hot. I have tightened...
  19. J

    19parts85 Evinrude 2 hp Water in Cylinder

    I have a 1985 Evinrude 2 hp E2RCOC that I am bringing back. At the end of last season, it was running pretty well. I should have left well enough alone.... I got the smashing idea that I should refresh its innards this winter. I replaced the water pump impeller, the gear case lower and upper...
  20. J

    1985 Evinrude E2RCOC Not Idling as Expected

    I have an E2RCOC that I am bringing back to life. After resolving some ignition leakage issues, I have the engine running. It starts great and runs at full throttle great, but, when I pull the throttle down to half or less, it stalls out. I thought some of it might have been caused by the...
Top