Search results

  1. M

    '84 Merc 150 - V6 2.0 - can't get powerhead off.

    I've got 10 9/16" nuts pulled off the powerhead. The 2 in the front aren't all the way off because I have to nudge the powerhead off the mid section far enough for the nut to slip out. As far as I can tell all 10 bolts are off (front 2 almost all the way off) but I can't so much as budge the...
  2. M

    '84 Merc 150 - throttle linkage problem

    1984 Mercury Black Max XR2 Serial number: 6532700 I've been working on the timing on my motor and got it running like a top today. After some time I was unable to get it up to speed to plane out. I could idle and could get it just to the point where it should level out and take off but it...
  3. M

    '84 Merc 150 - how do I adjust timing?

    1984 Mercury Black Max 150 XR2 Serial Number: 6532700 I'm reading conflicting information in 2 different manuals. I can't figure out how to set the timing. I'm supposed to find .462 BTDC using a dial indicator and set the timing pointer to a mark on the flywheel at .462 BTDC. So, is .462 BTDC...
  4. M

    '84 Merc. 150 - what is idle RPM?

    I've got a Seloc manual that refers to the appendix but the only rpm I see there is 5K which might be a bit high for idle speed (sarcastic). The manual does not have an idle speed in the specs. I've looked and can't find an RPM for the idle on this motor: 1984 Mercury Black Max XR2 Serial...
  5. M

    '84 Merc. 150 doesn't crank.

    I've got a Mercury 150 XR2 Ser. #6532700 I ran this boat about 2 months ago and have been having trouble with it idling right but the starter was cranking just fine. Now it won't crank. I can hear the solenoid click and I tested voltage to the + lead on the starter. When I turn the key to...
  6. M

    How Do I Charge Aux. Batteries

    I've got an '84 Bass Nautique with a Mercury Black Max 150, 1984. I realize that the motor's stator => rectifier recharges the battery that starts the motor. I've got 2 aux. batteries that run the instrument panel and the trolling motor. They're wired in series to get 24 volts for the trolling...
  7. M

    Mercury Marine Outboard - Black Max- Serial Number Location

    I searched this site and quite a few others, trying to find the serial number for my engine. I found numerous different answers, none of which seemed to apply to my motor. I hunted all over the block and everywhere I could to find the serial number on my Mercury Black Max 150 XR2. I finally...
  8. M

    '84 Merc. 150 - Won't Crank Anymore

    I'm working on my '84 Mercury Black Max 150 XR2. It's been running rough but started without TOO much trouble and if I could get it to plane it runs @ about 50 mph. I learned that I should do a de-carb procedure. But, before I learned that I disconnected the remote control wires expecting to...
  9. M

    '84 Merc. 150 - Low Compression - Now What?

    I've got a Mercury Black Max 150 XR2 that runs. I had trouble getting it up to speed on the water but once I did it ran over 50 mph. It ran that fast just last week. I started it again today with little difficulty. It doesn't like to idle and has a lot of trouble getting up to plane so I asked...
  10. M

    Bass Boat - Trim - Planing Problems

    I think I'm dealing with part lack of experience and part (the most part) faulty equipment. I've got a Bass Nautique w/ a Merc. Black Max 150 XR2 on it. When I first take off, I've got trim all the way down. The stern digs in and the bow shoots up. The motor does not rev up. As I move I pull...
  11. M

    Bass boat - planing problems or engine problems?

    Hi: I just got my Bass Nautique with a Merc. Black Max 150 XR2 in the water. Once I got it going it ran well. It's a fast boat. When I'm first trying to take off though, the stern digs into the water and the bow shoots up. The motor bogs and it won't take off. I'm not even sure how it finally...
  12. M

    My Merc BlackMax 150 XR2 won't start. Why?

    I bought a bass nautique with a Mercury BlackMax 150 XR2 about a month ago. When I bought it we took it out on a lake and it ran great. Now I can't get it to fire. It turns over but won't fire. I did add too much oil to the gas. The ratio is 50:1 gas:oil or 1 pint of oil to 6 gallons of gas...
View older results
Top