Search results

  1. W

    Dhadley, I need advice....

    I broke my stingray off a few days ago, and before I put a new one on I took the opertunity to test 11 different props today.<br /> I have an 18gal built-in tank and a 6 under the back. I filled only the 6 and ran each prop from A-B, and B-A, varying trim as needed. After each prop test, I...
  2. W

    Stingray torn off

    JB, dhadley, I hit the lake this eve., and after loading the livewell with whitebass & wipers, I took off and noticed it took a little more time to get on plane and the boat wanted to porpose like crazy. I had to keep it trimmed pretty level to keep things in order.<br /> When I got to the ramp...
  3. W

    Texoma Stripers

    Anyone have any advice as to Striper fishing Texoma without a guide??? Planing a trip in late Oct., or early November.<br /> I prefer trolling or casting, as I am not set-up to handle live shad..<br /> Any Ideas??????<br />T.I.A :)
  4. W

    Garmin fishing products

    Just wanted to say THANKS to the crew at GARMIN for taking care of a speed sensor problem for me and at NO CHARGE. They sent a new sensor (updated version) to replace what I totally expected to pay for!!!<br /> The best part is I talked with them on a weds., and Thurs. am., I had a ups overnite...
  5. W

    Under-priced props!!!!!

    Just venting some frustration here but iboats is selling a large selection of Ballistic props at a Price 40% lower than they normally sell for....Yea, I know, they're the "old" attwood Ballistics but I lost 2 sales over this because it's 50-70 bucks cheaper than we buy them for at so-called...
  6. W

    Nauticpro props

    Does anyone know about the Nauticpro SS props??<br /> I was told they were OMC but the number doesn't jive. P/N 3040073 13-3/8X17 Stainless steel.<br /> I was hoping maybe Joe Reeves might know, but any info would be great.<br /> I put this on the Jon/Evin-repair hoping it would get to the right...
  7. W

    TNT no-go

    I've got a Jonny115 crossflow, 97' model and all at once I lost my TNT. I've checked both relays-test good by OMC manual, I've tried to run trim motor by disconnecting pigtail under hood and applying 12vlts, no luck So I tested eng. side of pigtail-green and blue, and I show 12.5 volts on both...
  8. W

    T-N-T Gurus-Help

    Have neither up or down. I've tested relays per omc manual and both test good. I disconnected trim motor pig tail under hood and tried to make trim motor run with 12vlt supply...Zero...tested blue and green from engine side of pigtail, and I'm showing 12.5 volts on BOTH pins, without running...
  9. W

    Trim/tilt-no up or down

    Yesterday on the water drifting I always lift eng most of the way out of water, and after about 3 hours, and we were ready to go...No t-n-t up or down. I tried switch on side of eng. as well. relays inside box click when switch is pushed in either direction from front or back. If relays are...
  10. W

    Bombardier injection oil

    Can anyone tell me if this is ok to use in a pre-mix at 50:1.....115 Jonny 97" Model......
  11. W

    compression on rebuild

    The boys on the forums have me thinking maybe I've got compression- or the lack of, on my fresh rebuild 97 crossflow 115 Jonny. I bypassed the VRO, went to 50:1, but for break-in, 25:1.<br />After the first 6 hrs run time, 3 90's and a 95.<br />now at 20hrs and on 50:1 after 8 hours, I've got 3...
  12. W

    Prop shops

    Anyone know a shop that can repitch the Ballistic series props....I've got a 19"pitch, and I need to shallow er' up a bit for more R's.<br /> My shop in Denver can't do Ballistics for some reason-No molds maybe????? :confused:
  13. W

    Gimble ring

    cannot remove upper gimble pin, bolt is out of steering arm...using 5 lb slide-hammer to attempt to remove pin. Also have tried to heat steering arm. Any suggestions on removing upper pin?????????<br />Thanks!<br />p.s. We are following procedures listed in manual.<br />228 Mercruiser/305 chevy...
  14. W

    TRADE PROPS?

    Anyone got a 17p Ballistic for OMC 13spline that they would trade for a 19p??????? :rolleyes:
  15. W

    TRADE PROPS?

    Anyone got a 17p Ballistic for OMC 13spline that they would trade for a 19p??????? :rolleyes:
  16. W

    Stainless Props

    Can anyone tell me if and or who can repitch Ballistic props???? I know S.S. is hard to work with, but I've got a 13-3/8X19" for my 115 Johnson, and it won't spin it near fast enough........thx
  17. W

    repitching stainless props

    anyone know if a Ballistic 19" can be reworked to a 17"???........I know S.S. is harder to work with and my local Prop shop can't do the Ballistics........THX
  18. W

    Main Jets-115 Johnson

    I have a 115 Johnson that I recently O/H'd, and when I got to the carbs, it had 68C main jets. This engine came from Florida with #4 stuck....I found the pistons to be wisco's-20 over and the bore was only .018 over standard. Anyway, I opened the bore on all 4 to .021 over standard and installed...
View older results
Top