Search results

  1. 9

    2003 Yamaha F25 Runaway Throttle on Start

    motor needs more fuel and air to rev up or timing has to be advanced. if the throttle plates are still closed off, I would be checking to see what the timing is doing with a timing light
  2. 9

    2023 Yamaha 9.9 high thrust compression reading

    with that much scoring in that cylinder wall might indicate oil coming up past the rings fouling that one plug. did the other cylinder wall and piston look OK?
  3. 9

    2023 Yamaha 9.9 high thrust compression reading

    Since I cannot find a parts diagram for a 2023 motor, I am guessing it is like the 2022 so it has carbs with a choke. I do not understand how a 4 stroke motor would be carboning up so bad from just gas and no automatic enrichment system to fail and be dumping extra fuel into the motor when not...
  4. 9

    2023 Yamaha 9.9 high thrust compression reading

    a complete model number would be good to post when asking about a motor. Being a 2023 I believe it has to be a 4 stroke motor. what does the oil look like, and the level? being new, was it broken in properly. some motors not broken in properly dilute the oil with fuel and cause it to over fill...
  5. 9

    Yamaha 130 mounting height

    is it the same poster? If it is maybe altimers got a hold of him and does not remember asking/going thru this not long ago Yep just checked his posts and found this. https://forums.iboats.com/threads/yamaha-130-hp-20-shaft-mounting-height.770983/
  6. 9

    HPDI 150 won't stay running

    good to hear, thanks for posting the fix
  7. 9

    Speedo Tube

    I have no idea if you are looking for the place to hook it into on the console or at the motor from what you wrote
  8. 9

    Yamaha 130 hp v4 2 stroke

    how many wires do you have going into the motor? if just 2 disconnect from the relay and run some jumpers from a good battery to those wires to see if it runs , and then reverse the jumper wires to see if it goes that way too. bad brushes can be replaced, but rust and water inside is not...
  9. 9

    Yamaha 130 hp v4 2 stroke

    good chance the contacts in the relay are not making up good due to burnt contacts but jumper around the relay to see if the motor will turn before replacing the relay
  10. 9

    1997 Yamaha C90 Two Stroke Reverse Noise

    I believe that motor like most Yamahas I have played with are spring loaded into forward. you have to overcome the spring to get to neutral and reverse. put the controller into neutral, disconnect the cable at the motor make sure the motor lower unit and linkages are in the neutral position...
  11. 9

    2001 Suzuki DF140, won't crank, no spark

    just because the boat is a 2001 does not mean the motor is. find the motor ID info on the motor itself so you know what you are dealing with.
  12. 9

    Short circuit

    also might check to see if the Rectifier/regulator got smoked also, but I do not think that would keep the starter from tuning the motor
  13. 9

    85 hp yamaha 2 stroke not cranking when cold out side.

    for the motor to start and run the cylinders need to have good compression, good spark at the correct time, and the proper fuel to air mixture. when it is cold and will not fire up,chack comroession, check spark, check timing with a timing light, if all that is good then you are left with a fuel...
  14. 9

    Engine runs, but does not turn the prop

    while you are at it look to see if there is some evidence on the lower unit of a big shark showed up and tried to bite the prop off while it was running in those high seas
  15. 9

    85 hp yamaha 2 stroke not cranking when cold out side.

    crank and start are 2 different animals
  16. 9

    Yamaha 130 hp 20 " shaft mounting height

    from the pics you posted you motor will not be right next to the bottom of the boat. what am I missing?
  17. 9

    Yamaha water jacket corrosion

    looks like plenty of meat left on all sealing surfaces to me. I would remove as much build up to make sure cooling passages are clear and put it back together with new gaskets
  18. 9

    HPDI 150 won't stay running

    if the rail pressure is in spec as the motor dies, I do not see a fuel supply as a problem. but injectors all firing properly would be, along with spark and timing. just reread the original post and it says it only idles for 15 - 20 seconds. I believe I have read where those motors do not run...
  19. 9

    Yamaha 130 hp 20 " shaft mounting height

    why did OMC go out of business if they were so good?
  20. 9

    HPDI 150 won't stay running

    is the rail pressure in spec? I have no idea if what you posted is in spec or not
Top