Search results

  1. 9

    yamaha fourstroke crank bearings

    sounds like he needs to check the cam bearings line up after welding and before milling. If out , maybe line boring the cam holes and then see if you can find new cam bearings to fit the new hole size
  2. 9

    yamaha fourstroke crank bearings

    so is the warp of the head the problem or is the milling of the head surface the problem? if the head was not warped and all the cam bearing are still in line, then resurfacing the head should not be a problem, right?
  3. 9

    yamaha fourstroke crank bearings

    in line with what? I am failing to see how the alignment would change by resurfacing the head to block surface. the belt has tensioner to take up slack.
  4. 9

    Suzuki Dt16 Starter

    good to hear, thanks for updating what the problem was.
  5. 9

    Lower gearcase on 2005 f150

    may be like a friend that drained his lower but did not have the lube to put back in. thought he would pick up some next time in town and then forgot all about draining it
  6. 9

    Lower gearcase on 2005 f150

    pressure test it to find where and how bad it leaks. hard to believe all the lube leaked out and it was not also full of water
  7. 9

    2001 OX66 stumbles at idle after running wot

    Oh, so the line large was suppose to be linkage. the pressure regulator can be tested to make sure it does its thing correctly
  8. 9

    2001 OX66 stumbles at idle after running wot

    not sure what the changing of the oil pump has to do with your problem or what the line large hanging up is about. Or how changing the oil pump would affect the fuel pressure regulator screen. monitor the fuel pressure to see what it is doing when the problem shows up. moving the throttle...
  9. 9

    2001 OX66 stumbles at idle after running wot

    How many different OX66 did Yamaha produce in 2001? every one of them should have a model # on the bracket.
  10. 9

    2001 OX66 stumbles at idle after running wot

    strange, 3 years and still no one has a clue what motor you have
  11. 9

    Looking for pump to drain oil through dipstick tube

    fire the motor up and get it warmed up , shut off, and pump it out. long as you get the tube to the bottom of the pan it will be the same as pulling the drain plug. what do you think will be so heavy that it would settle out into the bottom of the pan and not be able to suck it out?
  12. 9

    Looking for pump to drain oil through dipstick tube

    what does what you fear have to do with his question?
  13. 9

    Suzuki DT 140 2 stroke carburetor version tilt and trim stuck in down position

    sorry, but I do not know much about a Suzuki motor. I have no idea what Suzuki does to limit tilt or even if it does
  14. 9

    2000 200hp Saltwater series 2 stroke SX200 spark plug

    normally there is a sticker on the motor somewhere indicaing what plugs should be in it. but a owners or service manual should give the proper information
  15. 9

    Suzuki Dt16 Starter

    is the side pressure you put on it acting as resistance to keep it from turning too easily which in turn causes it to rise instead of just freely turning around maybe
  16. 9

    Suzuki DT 140 2 stroke carburetor version tilt and trim stuck in down position

    if moving the motor around affects this, you have a bad connection or wire itself
  17. 9

    2001 DF70 won't go over 3000rpm

    thanks for the update , I do not think anyone could have guessed that was the problem I am sure you will double check things to make sure from now on. and others looking to solve similar problems will need to double check things they did also if they read this post
  18. 9

    Suzuki DT 140 2 stroke carburetor version tilt and trim stuck in down position

    if you have 12V+ heading to the T&T relay when you operate the switches either the relay is bad or you have a bad connection on the Pos or neg somewhere to the relay. have you tried jumping the relay to see if the relay or motor will operate?
  19. 9

    Suzuki Dt16 Starter

    if it fell out how would it work just sometimes?
  20. 9

    Boat going in reverse but not forward.

    since the OP did not give the motors model number we have no ideaa what it is. but Yamaha switched to a twist to shift in 1995 ,I would have to guess his 80s 40 is a push and pull shift rod. drop the lower unit again and place the lower unit in reverse and the shifter in reverse and hook back...
Top