Recent content by Roadside Design

  1. R

    1959 Luger Fleetwood Restoration: Getting my feet wet.

    Its kinda like taking the riding mower for a spin out on the highway, but the little 18 is on and wired. Wife wasn't a big fan of the factory color, so I made some changes in the spray booth and shot the lower unit a silver, similar in tone to the factory blue and left the blueish top stripe off...
  2. R

    1960 Evinrude 18 tiller removal cover?

    Im purchasing a 1960 18 hp twin to occasionally swap with my 1959 50hp gas hog, something to allow me to run on restricted horsepower lakes in my area. I'm set up for remote steer and start and would like to remove the handle. Is there a cover that goes in place? If so what is it called? Thanks
  3. R

    1959 Luger Fleetwood Restoration: Getting my feet wet.

    It was a crazy week with work, kids and the swapping of lower unit internals. In the end... We made it! The old Starflight coughed and choked at first, but roared to life, after the first 5 mins that thing accelerated hard and left me with a huge smile! By the end of the weekend I made 3 short...
  4. R

    1959 Evinrude color formula needed asap!

    Trying to get the boat on water in the next 4 days, we need to repaint the lower unit. Does anyone have a color code I can reference for Polychromatic Grey? My Nason paint supplier needs numbers and last scans came back way off. This is a 1959 Starflight 50. Note '59 shows Platinum Mist, we...
  5. R

    Bringing life to a mint '59 Starflight 50

    Ok guys, need your advice. The boat I have been restoring was blessed with a 1959 Evinrude Starflight, the condition was outstanding with ultra low hours and beautiful paint. (Boat resto here goo.gl/0E9aNZ ). It has one flaw on the lower unit I'll address later. The great news is the engine is...
  6. R

    1959 Luger Fleetwood Restoration: Getting my feet wet.

    Thanks guys, So next week will be the small stuff, fuel tank mounting, light wiring and seat installation. Then to the engine. Unfortunately previous owner did a number on the lower unit housing, he wanted to replace a leaky seal and broke off the lower casting. JB Weld can do a lot of things...
  7. R

    1959 Luger Fleetwood Restoration: Getting my feet wet.

    No Title I posted too soon, the rest of the seats arrived last night! great work.
  8. R

    1959 Luger Fleetwood Restoration: Getting my feet wet.

    Wow! Both seat bases arrived from Nauti-Upholstery in Florida! So glad I went with the seat pads instead of doing a full traditional seat, this is closer to what this kind of boat should have had and dig the look. The quality fit and finish of these exceeds my expectations, perfect fit . Hope...
  9. R

    1959 Luger Fleetwood Restoration: Getting my feet wet.

    Happy timing! I search on ebay for Luger often with the usual result of a small ads showing up for sale, nothing else. Then last week a repoped a Luger nameplate! Never seen one so bought it, sent a message and he had a second one too. I was almost done with the art for side decals so the timing...
  10. R

    1959 Luger Fleetwood Restoration: Getting my feet wet.

    When I purchased the boat there was a ski bar to clear the outboard, at first glance I assumed it was a 1980's part and almost tossed in a dumpster on the way home. Good thing I didn't! After some inspection realized it was mounted on the boat when built and still had the holes and mounting...
  11. R

    1959 Luger Fleetwood Restoration: Getting my feet wet.

    Also wrapped up the dash install, original paint on the wheel!
  12. R

    1959 Luger Fleetwood Restoration: Getting my feet wet.

    Two more things checked off the list: I needed a transom saver, I did a little fabrication since the trailer was modified. I welded a couple angle brackets to the frame rails and added cross bar that easily removes with a couple quick pins. Seems solid.
  13. R

    1959 Luger Fleetwood Restoration: Getting my feet wet.

    All the side carpet was installed over the weekend and I finished the control unit last night. The control cables were 12-18" too long so I cut them for a better fit, it was easier than I thought. I believe I have all parts needed being shipped and have a long list of small install items and...
  14. R

    1959 Luger Fleetwood Restoration: Getting my feet wet.

    Coming Unglued. I found a great inexpensive flooring product I love. When I bought it they said to use this water based contact environmentally friendly can of crap, followed directions to the letter, even heated the garage and it failed. I used good old toxic industrial rubber cement in the...
  15. R

    1959 Luger Fleetwood Restoration: Getting my feet wet.

    And to last weekend... with great weather I took advantage and painted the engine cover. In a way I felt guilty, the paint was great and sure any collector would have polished it up. There were two or three chips and the paint over the fiberglass had shrunk which was ok, but my boat is black red...
Top