Will check the ones I can get too. Will add the boat is stored and has been its whole life in a climate controlled garage and not in freezing or hot weather. Nothing is dry rotted or cracked up from elements
I have a 2013 60hp efi 4 stroke that I have owned since new. The problem is it had a miss that only starts around 4500rpm. Sometimes it runs great some times it misses every few seconds. Higher rpm has even more miss. Under 4500 rpm ot runs perfect all day. I was told it was probably the fuel...
I just bought 4 new plugs for my 2012 60hp 4 stroke RA8HC same as what's in it but the new plugs electrode is way taller than the old plug. The old plug in pic is gapped at .040. the new plug is gapped .025 if I gap the new plug to .040 the end is way up and not parallel with the center. The guy...
I got a question about voltage. i have a 12V power bubbler for my bait tank Power Bubbles Aerator | Bass Pro Shops and was wondering will it hurt the bubbler or shorten the life of it to run on the cranking battery which produces 13.6+ volts when the engine is running? didnt know if it would...
ok guys and gals. i got a 1974 evinrude 70HP 3 cylinder that i have owned for 10 years. iv done all of the work myself on it and when i took it out the other day it stalled on me taking off. when i crank the engine up i have always had to choke it warm or not but it always fire right up when i...
ok guys and gals i need some help. I have a 1974 evinrude 70hp engine that i have owned since 2002. Iv had 1 coil pack go bad and i replaced power pack and stator since i have owned it. its got brand new spark plugs gapped at .030 QL77JC4. all spark plugs have good fire. electric choke does not...
OK guys and gals. iv owned plenty of older boats and now im ready to bite the bullet and buy me a new boat. need your thoughts on motors
i got my mind on the 4 stroke 90HP mercury because from what i read the 4 strokes are easier to start, runs quieter and dont have to mix gas and oil.
my...
ok guys heres the story. 70HP evinrude took it out fired right up ran it about a mile up lake and it started cutting out loss of power. it would try to go then lose all power and would only run like 10mph wide open. it idles perfect but when you put it in gear it just bogs and dies everytime...
I just ordered new spark plugs for my 1974 evinrude 70hp 3 cylinder and i ordered what it calls for UL77V but the person sent me QL77CC. Will these plugs work as a replacement for my motor since they are still 77 series? i have ran the QL77JC4 in it and they run good gapped at 0.030. the ones my...
ok guys and gals im having a problem with my minn kota power drive 40lb thrust trolling motor. it has the foot controller with 25 ft cord on it and adjustable speeds from 0 to 10. here is a pic of my pedal.
http://www.northlandmarine.com/images/MinnKotaPowerDriveFootPedalAssy.jpg
Now here is...
ok guys and gals. i got a 2 bank 4amp/4amp onboard battery charger. it is sealed and waterproof. i read from the website that i can hook both leads to 1 battery for charging 1 at a time? is this ok to do? first time i used it it got really hot but charged the battery. just dont want to screw...
ok guys and gals i have a 1969 OMC stinger stern drive electric shift thats hooked to a 4 cylinder gm 120hp. i found another stringer lower unit on a blown motor thats in great shape for the year! idk what year or model it is but it is electric shift just like mine and it looks just like mine...
I have a 1976 mercury 20hp boat motor and it has been sitting for 2-3 years. i got it out today and hooked up muffs to it and flushed it out good and fired it up and it was peeing water. after about a minute i noticed it stopped peeing and i thought it was just my muffs not sealing good on the...
I currently have a 14" with 16 pitch and it looks rough and chipped pretty bad. its not cutting water very well at all. I want to keep the size and pitch the same because it seems to run good with it but i cant find a 14" 16 pitch anywhere? The motor turns about 5400-5500 rpm with the prop now...
Is it hard to change the water intake screens on the lower unit? the screens are made of plastic on the Johnson and i guess they set and got weather cracked and busted out over time. here is a picture of the screen im talking about.
http://img.photobucket.com/albums/v336/darksky65/screen.jpg
