Shop
Community
Home
Forums
New posts
Search forums
What's new
New posts
New media
New resources
Latest activity
Media
New media
New comments
Search media
Resources
Latest reviews
Search resources
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Current visitors
Menu
Log in
Register
Install the app
Install
Home
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Mc Tool's latest activity
M
Mc Tool
replied to the thread
What is This? It has Mercury on it.
.
argh craparama here we go again ! I remember all the bickering over this topic last time , that planes use pitot tubes for airspeed...
Sep 27, 2026
M
Mc Tool
replied to the thread
Repowering my old 16ft aluminum boat thinking of going 4 stroke but have a question
.
Whats your mechanical ability ? My plan is to buy a known tired 4 stroke ( poss x charter boat motor ... well serviced but high hours...
Sep 27, 2026
M
Mc Tool
reacted to
racerone's post
in the thread
Repowering my old 16ft aluminum boat thinking of going 4 stroke but have a question
with
Like
.
No such thing as a 2 stroke ( in good condition ) that is hard to start.----In my opinion most folks are unaware of how to maintain...
Sep 27, 2026
M
Mc Tool
replied to the thread
What is This? It has Mercury on it.
.
Its a speedo pick up ....water is forced up that tube and goes to a pressure gauge on the dash that has mph on the dial .....pretty...
Sep 27, 2026
M
Mc Tool
replied to the thread
Someone else's outboard conversion fail
.
Im with Chris in that if its what you have and you need to make it work with a limited budget ( doesnt look like a high budget outfit...
Sep 27, 2026
M
Mc Tool
reacted to
Chris1956's post
in the thread
Someone else's outboard conversion fail
with
Like
.
Gee, so many negative vibes. Put the trailer up on ramps, like when changing your oil.
Sep 27, 2026
M
Mc Tool
reacted to
Chris1956's post
in the thread
Someone else's outboard conversion fail
with
Like
.
To be fair, the motor is just a bit low. If it was up a few inches, and you never plan to tilt it up, run it!
Sep 27, 2026
M
Mc Tool
replied to the thread
portable fuel tank quick disconnect
.
My main motovation was ....with both 2 and 4 stroke motors on the same boat , was to make sure one could not hook up the wrong tank...
Sep 27, 2026
M
Mc Tool
replied to the thread
Random
.
who, me ? :LOL:............probly a pie and Coke
Sep 27, 2026
M
Mc Tool
replied to the thread
8hp Johnson idles well, but stumbles under load, sometimes
.
Yeah OK , what I would do is, firstly check that choke butterfly is closing , if it is, then with a cold motor , to open the carb bowl...
Sep 26, 2026
M
Mc Tool
replied to the thread
Random
.
🤢Yeah Ive done that after a hard night :D
Sep 26, 2026
M
Mc Tool
replied to the thread
8hp Johnson idles well, but stumbles under load, sometimes
.
Hard to start cold could be a choke issue....couple of things to check , The choke plate butterfly in the carb must be fully closed...
Sep 26, 2026
M
Mc Tool
replied to the thread
portable fuel tank quick disconnect
.
yeah me too :)
Sep 26, 2026
M
Mc Tool
replied to the thread
Stuck Steering
.
Well send me one for a start :LOL: , but yeah , doesnt take much thinkin about . I guess you could remove the tilt tube with the...
Sep 25, 2026
M
Mc Tool
replied to the thread
Stuck Steering
.
FFFFFar out , thats even worse than mine . I couldnt easily find another tilt tube for my motor and being that the steering rod was...
Sep 25, 2026
Home
Members
Top