I Have A 92 Mercury 20hp. It is idiling higher then normal, and there is no idle adjustment on this model. Just a mixture screw. It seems ok in the lower RPM range but will stutter and shake and not go to full power at all? Carbs are cleaned and spark is good to the plugs. I am stuck and ready...
Ok Fellas I am trying to figure out what is the problem is with my 92 Merc 20hp manual start.
It starts right up within 2 pulls, it seems to be idling higher then it should, and I cant find any adjustments but the low speed idle screw and I did adjust the screw back and forth to 1 1/4 to 1...
I am looking for some info on how to obtain a control box that is compatiable for a 94 25hp Marnier. It sems the ones I have were for a bigger merc engines and the throw is going the wrong direction for my engine? Is there anyway to switch around the box I have and reverse the throw? The...
Hello My motor is a 25 hp Mariner.I would like to know the year of the motor first. The serial number is 0G023000. I have Throttle and shift control cables installed already but no ignition box. I have a Mercury Quicksilver control box with a 8 pin harness. The harness went in nicely and...
Hi I was wondering if anyone has ever hooked up A tach on A 1985 Suzuki? There appears to be no hook up on the older style motors like there is on A 1986 and up , I was wondering if I could get any feedback on how to do this? I have tried to do it through the control box because there are wires...
Hello I have late 80's Evinrude 40hp and I did A compression test on it and the top was A solid 140 and held and when I checked the bottom it flew up to 140 the released down very fast? I just wanted to get some info if any takers ever heard of this? Before I go getting it taken apart,I was...
Hello I have late 80's Evinrude 40hp and I did A compression test on it and the top was A solid 140 and held and when I checked the bottom it flew up to 140 the released down very fast? I just wanted to get some info if any takers ever heard of this? Before I go getting it taken apart,I was...
Hello, <br /><br />I have a mercury 2.2 the serial number is 9094762 if anyone knows how I can find out what year it is it would be greatly appreciated.<br /><br />Thanks in advance.
I have a 40 hp Mariner I was told it was a 1980 but I want to make sure. I included a picture of the label. Mariner 40BM 676 B 304047 <br />Thanks in advance.<br />
I have a Nissan 9.9 long shaft but cannot find any info on what year it is. Im looking to find out some more info. Please let me know. <br /> <br />NS9.9B2 335A-1 54740 <br /><br />Thanks
Anyone have a used cowling for 1988 DT140 Oil injection? Please let me know if you know where I can find one or if someone has one. <br /><br /><br />Thanks
I have a Suzuki Dt140 the Numbers on the plate say 14002 811460 I know its a 140 4 cyl but dont know what year. I also need to know if Suzuki offers a steering arm that attaches to the motor through the tilt tube on the front of the motor?
I have a 40 hp VRO Johnson with a 12 1/2 X 13 prop. I have no problems getting out of the hole. The motor is reaching max rpms and the boat speed is only about 21 mph. Could changing the pitch of the prop give me more speed at the same rpm? Any suggestions on what pitch I should get. Thanks
Ok I have a 1999 Mercrusier 5.7 when I go to start motor, starts just fine at first, then stalls. Starts back up same thing. Tested Fuel pump volt meter it only gets voltage when starter engages, when the key is in the run pos. vols drop to 0, tested charging system at battery and it was at 13.9...
