Search results

  1. B

    Will a Stator Or Timer Base Make Your Motor Idle High And Have No Power A WOT?

    I Have A 92 Mercury 20hp. It is idiling higher then normal, and there is no idle adjustment on this model. Just a mixture screw. It seems ok in the lower RPM range but will stutter and shake and not go to full power at all? Carbs are cleaned and spark is good to the plugs. I am stuck and ready...
  2. B

    20Hp Mercury High Idle And Sputtering @ WOT

    Ok Fellas I am trying to figure out what is the problem is with my 92 Merc 20hp manual start. It starts right up within 2 pulls, it seems to be idling higher then it should, and I cant find any adjustments but the low speed idle screw and I did adjust the screw back and forth to 1 1/4 to 1...
  3. B

    1994 25 hp Mariner Side Mount Controls

    I am looking for some info on how to obtain a control box that is compatiable for a 94 25hp Marnier. It sems the ones I have were for a bigger merc engines and the throw is going the wrong direction for my engine? Is there anyway to switch around the box I have and reverse the throw? The...
  4. B

    Mariner Tracker Motor ?

    Hello My motor is a 25 hp Mariner.I would like to know the year of the motor first. The serial number is 0G023000. I have Throttle and shift control cables installed already but no ignition box. I have a Mercury Quicksilver control box with a 8 pin harness. The harness went in nicely and...
  5. B

    1985 Suzuki DT140 tach harness ?'s

    Hi I was wondering if anyone has ever hooked up A tach on A 1985 Suzuki? There appears to be no hook up on the older style motors like there is on A 1986 and up , I was wondering if I could get any feedback on how to do this? I have tried to do it through the control box because there are wires...
  6. B

    compression test ? Evinrude 40hp Late 80's

    Hello I have late 80's Evinrude 40hp and I did A compression test on it and the top was A solid 140 and held and when I checked the bottom it flew up to 140 the released down very fast? I just wanted to get some info if any takers ever heard of this? Before I go getting it taken apart,I was...
  7. B

    Compression Question Late 80's Evinrude 40hp

    Hello I have late 80's Evinrude 40hp and I did A compression test on it and the top was A solid 140 and held and when I checked the bottom it flew up to 140 the released down very fast? I just wanted to get some info if any takers ever heard of this? Before I go getting it taken apart,I was...
  8. B

    Mercury 2.2 Need to find out what year?

    Hello, <br /><br />I have a mercury 2.2 the serial number is 9094762 if anyone knows how I can find out what year it is it would be greatly appreciated.<br /><br />Thanks in advance.
  9. B

    9.8 Mercury Model # 5455772 Need To know Year?

    I would like to know the year of this mercury 9.8 Model #5455772 If anyone can help that would be great.<br /><br />Thanks Again
  10. B

    Need to know the year of my 40hp Mariner

    I have a 40 hp Mariner I was told it was a 1980 but I want to make sure. I included a picture of the label. Mariner 40BM 676 B 304047 <br />Thanks in advance.<br />
  11. B

    Nissan 9.9 Make and model ?

    I have a Nissan 9.9 long shaft but cannot find any info on what year it is. Im looking to find out some more info. Please let me know. <br /> <br />NS9.9B2 335A-1 54740 <br /><br />Thanks
  12. B

    1988 Suzuki DT140 Cowling?

    Anyone have a used cowling for 1988 DT140 Oil injection? Please let me know if you know where I can find one or if someone has one. <br /><br /><br />Thanks
  13. B

    Suzuki DT140 Need to know what year?

    I have a Suzuki Dt140 the Numbers on the plate say 14002 811460 I know its a 140 4 cyl but dont know what year. I also need to know if Suzuki offers a steering arm that attaches to the motor through the tilt tube on the front of the motor?
  14. B

    Prop upgrade question

    I have a 40 hp VRO Johnson with a 12 1/2 X 13 prop. I have no problems getting out of the hole. The motor is reaching max rpms and the boat speed is only about 21 mph. Could changing the pitch of the prop give me more speed at the same rpm? Any suggestions on what pitch I should get. Thanks
  15. B

    1999 Mercruiser 5.7 Fuel pump gets power only when starter engaged ?

    Ok I have a 1999 Mercrusier 5.7 when I go to start motor, starts just fine at first, then stalls. Starts back up same thing. Tested Fuel pump volt meter it only gets voltage when starter engages, when the key is in the run pos. vols drop to 0, tested charging system at battery and it was at 13.9...
  16. B

    Need to know how much my motor weighs?

    Hello, I have a 1984 30 hp Johnson seahorse long shaft motor. The model number is J30ELCRR and the serial number is E5919349. Does anyone know where I can find the specs of the motor or does anyone know the specs. All I need to know is the weight. Here is a picture of the motor
  17. B

    Evinrude Lower Unit Question.

    I was wondering if anyone knows if a lower unit from a Evinrude 1972 55 hp with a shaft measurement of 17 3/4 would fit on a evinrude 1985 40 hp unsure of the lenght of the shaft on this one. To me they look exactly the same. <br /><br />Thank you.
  18. B

    1974 evinrude 15 Hp Push Button Start

    I recently picked up this little motor and was told that it had push button starting. Can someone tell me or give a diagram to show me where to hook up the battery to.<br /><br />Thank you
  19. B

    Evinrude 15 hp can't pull start locked up and don't know the year

    The motor was running fine with no problems. I went to take it out the other day and I could not pull start the motor it was stuck. Does anyone have any suggestions on what I can try to get this motor going again. <br /><br />P.S. if anyone knows the year of this motor it would also be...
  20. B

    Sears Gamefisher 5.0 Need to know the Year

    The model number is 217-585460 and the serial number is 08 171082 or 03 171082 If anyone knows the year it would be greatly appreciated.
Top