Hello OBJ or anyone,<br /><br />I am posting an additional topic from my fuel pump question a few days ago. O.k. I took off my coils and cleaned the metal grounds and where they connected to the engine also on all of them the ones on the #1 and #4 had a little film of something maybe a slight...
Hello,<br /><br />I have a question. My motor runs O.K. except that on the idle side it idles o.k. at first for no longer than a minute after comming back down from half or full throttle and then it dies. I can get it to statrt if I put the warm up lever up a little. It runs fine at all other...
Hello everyone,<br /><br /> I just got back from a good weekend at Rend Lake Illinois. Anyway my boat ran fine the whole weekend, but after I got back in for the day I decided to give my father a call in South Carolina. Anyway, he was asking me if I ran 93 Octane fuel in my motor and I told him...
Hello guys,<br /><br />I have a question. Today I went out to Kaskaskia River and took the boat out today. I previously had a problem a week ago with starting so I replaced the solenoid. Today I went to start my outbaord after pulling someone on a tube and it would not start I only had a tapping...
Good day everyone,<br /><br />I have a question concerning a 2000 Chevrolet Venture minivan that my neighbor owns. Yesterday my neighbor was comming home for work and his van died on him and had to get it towed back to his home which is a few houses down from me. Anyway he wanted me to look at...
Hello Everyone,<br /><br /> I finally took a long awiting vacation this past Memorial Day weekned and went to Rend Lake in Southern Illinois to do some boating/camping. Anyway, I went out for the second time last Friday with my boat and my wife wnated to be pulled on the tube so I did that for...
Hello Guys,<br /><br />I have a question on a prop. Will the diameter on a 12 3/4 X 21 and a 14 X 19 change the RPM's. What I am asking is will going from 14 X 19 prop that is turning 5000 RPM's go up when I change the prop to a 12 3/4 X 21 prop since the diameter of the prop is smaller or will...
Hello,<br />I have a quick question. I am bidding on a 13 1/4 X 17 prop aluminum on Ebay for my boat and was wondering if part# 700B and 382764 that is stamped on the prop will work on a 1989 Evinrude 88 horsepower SPL V-4 model# E88MSLCER? Thanks, Bob
Good day and what an AWESOME! forum,<br /> <br /> Anyway I have a question. The last time I went out in my boat I let my daughter and her friend tske turns steering the boat at a very slight speed not even 5 MPH for about 30-40 minutes, anyway I had a good pee stream and my question is is it...
Hello,<br /><br />I have a prop question. Will going from a 12 3/4" X 21 pitch to a 14 X 19 prop change the RPM's? What I am asking is since the diameter is bigger(14") and the pitch lower(19") do to the surface area of the prop area will my RPM's go up or would they balance out? I am thinking...
Hello everyone,<br /><br /> I have a question. I am helping my father locate a intake manifold for a 2 barrel holly carbuertor. It goes on a Cobra outdrive OMC 3.0 liter 4 cylinder model# 302BMRJUB serial# T01260315. If anyone out there has one or knows where I can buy/purchase this part can you...
Hello,<br /><br />I am finally going to take my boat out tommorrow for the first time this year with me and my family. My question is I put fuel stabilizer in my gas tank and I hope the gas is still good. The last time I filled it up was in October 2005 and it is a full tank of gas with...
Hello everyone,<br /><br />I got a quick question. I want to remove the gas from my boats gas tank that has been there since October 2005 last year. I was wondering if I could put that gas in my 1999 Chevrolet Silverado so I don't waste it. It has fuel stabilizer in it but I just wanted to put...
Hello,<br /><br />I have a prop question. Currently I have a 1989 Evinrude V-4 88 horsepower SPL model# E88MSLCER outboard. I currently ran a 12 3/4 X 21 sized prop, but I brought a 14 X 19 genuine Evinrude/Johnson prop brand new made for a 45 thru 115 V-4 outboard. Will this work allright on my...
Hello,<br /><br />I checked out my overheat system on my boat. I think it is working fine. What I did is ground out each cylinder bank and the alarm in the remote control went off at each side. I also ran my motor on the water muffs for about 10 minutes and the alarm never went off. In fact it...
