cooling issue?

JayIsHavingIssues

Recruit
Thread starter
Joined
Apr 8, 2017
Messages
2
I have been researching my 1970 Evinrude 60hp 60073D model, i am hearing there is no tell tale hole on these engines, so wondering how can i be sure its cooling and not doing any damage to my motor?
I have hooked the "ear muffs" up and ran it, runs like a champ, but i don't feel any suction at the intake. Am planning to replace the water pump anyway as this motor is new to me and its cheap, but going forward, whats the safe way to know im properly cooling?

2nd, i do not currently have power trim and tilt, looking to maybe install. Is it possible and just a kit, and is it affordable enough to be worth it?

Thanks alot
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,699
That engine has an overheat horn that if it sounds, will just about make you want to jump out of the boat. You can test the horn by grounding the lead going to the temp sensor. Testing of the sensor is a bit more difficult and If I recall requires some disassembly of the cylinder head. Although the engine does not have a tel-tale, it will spit some water out of the idle relief holes. The surest way to ensure cooling is to do regular impeller changes, and testing of the thermostat.
As for Power Trim, on 1970 engines only power tilt was available, Power trim was never offered for any engine pre 1973. If you want Trim, aftermarket systems like CNCs are available
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
A 1970 control box came with a " hot warning " light.--------Now this warning light is small and not in your line of sight.---------Installing a warning buzzer is a very good upgrade to do.-----------If you are unsure of the age of the impeller you should install a new one.-------Can be simple to install a telltale and there may be a spot already drilled / tapped at the top of the head / block.
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,699
Oops, you're right Racer about the light instead of a horn.:embarassed:
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Testing the overheat sensor is a waste of time. OK, so you put it in hot water and it worked. But will it work next time?? However, testing the overheat light/horn may have some value. All you have to do is ground the tan wire going to the sensor (with key turned on). Of course there is no guarantee it will work next time either, but at least it isn't such a difficult test to make.

The best assurance of reliable cooling is a fresh impeller. Does anybody actually drive their boat with their head cranked around backwards all day to watch the tell-tale? Or keep their eyes glued to the hot light? It only takes a few seconds to cook a motor if the pump fails suddenly. An overheat horn is the best system, but they are not 100% reliable either.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Push button control box? Shifting OK? The electric shift gear case works well and you can troubleshoot and maintain it -- but good to check it out early, if you have it, and do some prep work. (I had the 85 hp version for a number of years with no problems at all.)
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
whats the safe way to know im properly cooling?

An infrared sensor is useful for working on the cooling system. Temp on top of the head should be in the range of 130-140F or so. 160F is too hot. Test with the lower unit deep in a tub or barrel, or in the lake.

When working on the impeller, it's a good time to drain the gear oil. Check it for water (milky color). Refill with gear oil specified for electric shift lower units, assuming that's what you have. (Oil will be thinner than what is used in mechanical gear cases.)
 

JayIsHavingIssues

Recruit
Thread starter
Joined
Apr 8, 2017
Messages
2
thanks guys, noticed a hot light on the control box, will run some tests and see how it goes. ordered a new impeller. and a few other parts from this site actually, no idea when they will come but will keep informed incase anyone has the same issue.
 
Top