76' 75hp Stinger

Kbreal

Cadet
Thread starter
Joined
Mar 2, 2016
Messages
7
Hello guys,
I am in need of some advice on a older Johnson 75hp Stinger long shaft. I had a blown head gasket last fall. I found a dealer who replaced all gaskets, and went through all the carbs. New tank, and lines. I've only ran it twice, before the ice set in, but here is my problem.
No water intrusion now, runs smooth, however top cylinder seems to be running lean. The two bottom cylinders plugs look normal. All three cylinders came back good when I ran a compression test. 120, 120, 118. The Pistons, rings looked ok. No scarring, pitting, etc...
This week I ran through the carbs, and ran it in the garage, and did comp. test again.
Unfortunately, I'm stumped, or don't want to admit it to myself.... Top crank seal????
The mechanic was more than fair on price for last fall, but wondering what thoughts are on tackling this myself, or repower??? ( mechanics suggestion)
Note: family boat bought from the wife's side. She grew up on this rig, so...:) trying to do the right thing here! :) I had planned on new seats and paint! Lol. I think we have all been there!
Anyone tackle anything like this, or should I cut my losses?
Thanks for any suggestions you have! Kinda stumped, and don't want to be the one to burn the motor up!
 
Last edited:

Kbreal

Cadet
Thread starter
Joined
Mar 2, 2016
Messages
7
Also, to note ran a spark test last night also. Came back fine. Also, ran fine at WOT, RPM within range.
 

Kbreal

Cadet
Thread starter
Joined
Mar 2, 2016
Messages
7
What makes you think the top cylinder is lean.

On the two runs I was able to make, I ran at WOT, and low speed for a couple hour runs on new plugs. The two bottom plugs were showing carbon buildup, identical. The top plug was like brand new, but did have fuel on it. Did not show white, which I take as water burn-off?
Does that sound like normal, on a three cylinder?
Thanks for the response! :)
 

Kbreal

Cadet
Thread starter
Joined
Mar 2, 2016
Messages
7
Did you put new plugs in the motor or reuse the old plugs
New plugs on bothe runs. I was checking for water. We assumed it was the exhaust port gasket, or the head. Changed all gaskets easily accessed to be sure. I was ready to do that myself, but the mechanic had everything in stock with two hundred labor. However, he said if that didn't do it, he would just repower, which is why I've been tormenting myself.:)
First 3 cylinder I've dealt with, so was concerned when I saw the top plug. I know two runs aren't much. I just don't want to put my money on the hull, when I should be concerned with the motor.
The hull is a Cherokee, seems like a nice boat. All original. Thought it would make a nice restoration.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
Relax,----First check the top cylinder for strong spark.--It must jump a gap of 3/8" or more.---Does it do that ?----Then remove the low speed jet found in the bottom of the top carburetor,-----You might also consider removing the top carburetor to check the reed valves.----A new plug staying white indicates no fuel or no spark.----But that is my diagnoses from 1000 miles away !
 

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
8,348
Yes check for spark since you have fuel on the plug it's not burning. Do you have a tach on your boat and if you do what RPMs were you turning at WOT
 
Last edited:

Kbreal

Cadet
Thread starter
Joined
Mar 2, 2016
Messages
7
Thanks guys. I've rebuilt the carbs full kit, and the mechanic went through after. He checked the reeds, also. Checked for spark. Good to go there.
I think I'll pay him for a once over again this spring before I spend money on the old girls new lip stick. Appreciate the input. Probably putting to much thought on it. I'm a nut on maintance, which paid off when I found the water quickly. She does run smooth now.
 

Kbreal

Cadet
Thread starter
Joined
Mar 2, 2016
Messages
7
Flyingscott, I did not come with a tach. planning on running one this spring, also the mechanic added a pee hole to verify pump.
I agree I'm wondering about RPM's also.
GPS reading at 32 at WOT. Seemed right, sounded right, but new to me boat, so....
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
You can get two different plug readings, depending on whether the engine was shut off at idle, or at 5000 rpm's. Shut off at idle, the plugs may appear dark, and well lubed with fuel/oil. If you shut the engine off at 5000 rpm's, but leave it in gear, that's like reading the plugs at idle. As the engine slows down, the prop will continue to turn, lubbing the plugs-they may look the same as at idle. If you want to know what they look like at 5000 rpm's, shut the engine off, and immediately pull the shifter back to neutral. Don't let the prop continue to turn the engine over while you slow down. A high speed cutoff at 5000 rpm's should show the plugs a light tan in color- and dry. I share your concern about the top plug. No chance there is any water in that cyl that is washing the fuel/oil? I'd at least pull the top carb off and check the high/idle jet to see that it is not restricted with debris.
 

Kbreal

Cadet
Thread starter
Joined
Mar 2, 2016
Messages
7
You can get two different plug readings, depending on whether the engine was shut off at idle, or at 5000 rpm's. Shut off at idle, the plugs may appear dark, and well lubed with fuel/oil. If you shut the engine off at 5000 rpm's, but leave it in gear, that's like reading the plugs at idle. As the engine slows down, the prop will continue to turn, lubbing the plugs-they may look the same as at idle. If you want to know what they look like at 5000 rpm's, shut the engine off, and immediately pull the shifter back to neutral. Don't let the prop continue to turn the engine over while you slow down. A high speed cutoff at 5000 rpm's should show the plugs a light tan in color- and dry. I share your concern about the top plug. No chance there is any water in that cyl that is washing the fuel/oil? I'd at least pull the top carb off and check the high/idle jet to see that it is not restricted with debris.

Good call sir. There very well could be water, just not as bad, as it was before. I'll keep checking. Appreciate everyone's thoughts. I've checked spark, several times, but need to use a true tester. I've only done the old school ground and visual check. The plug has not had the white film look, it had before.
Planning on more testing this weekend, however my shade tree abilities, are amateur at best. Still a foot of ice here, so can't rev her that high on the muffs. The high speed jets have been gone through several times, but I know that has been missed by many before! Hoping that's the cause. Certainly, where I started, but sometimes going back to the start is what needs to be done. I only came to the conclusion of crank seals, from past threads. Hoping that's not correct!
Luckily, the wife didn't talk me into selling my other boat, even if the garage is full. Lol
 
Top