Search results

  1. C

    1975 johnson 115 hp.

    motor ran fine the last time about 2 month ago .today it fired 1 time and would not start checked plugs and found no spark could this be a bad power pack, any help .thanks
  2. C

    paul moir or someone64 40 hp lower crank seals

    paul moir or someone64 40 hp lower crank seals my old seals on the bottom crank had one 1 seal guess was a carbon seal my gasket set came with 2 seals do they replace the old one and how are they to be installed see pics<br /> http://community.webshots.com/user/cluke3
  3. C

    64 40 hp rebuild

    the book shows 2 orings on the crank upper and lower bearings do they slide on the bearing and fit in the groove in the block when i took it apart there was no oring on the lower
  4. C

    64 johnson 40hp bore

    had the bore checked on my other engine 3.184 is this within specs if so i plan on rering.
  5. C

    40hp rds22 update

    pulled flywheel key was ok screw was missing from one point set that holds the coil and condenser wires on think this was my problem.
  6. C

    problems cat transplant help rds-22

    2nd day out started and ran good shut down for about 1 hour went to re start hard to start then at full throttle all of sudden started missing and lost power idled but still missed shut it down and tryed to restart and it srarted backfiring i think thur the exaust will it do this if the crank...
  7. C

    rds22 on the river

    thanks to everyone for all the help had her on the river yesterday starts idles and runs good. hope no more problems with this one for a while.
  8. C

    1960 rds22 brass shift connector

    the long slot that runs the lenth of the connector do it face the front or rear
  9. C

    tiny tach

    what model would i need for my 64 40 hp
  10. C

    rds22 shipmaster control

    what is the procedure to replace the shift cable or how do you adjust it.
  11. C

    64 40 hp hot air electric choke

    any know the adjustment procedure for the choke my manual dont explain it
  12. C

    safety switch 64 40 hp

    anyone have a diaigram of how the safty switch and vac. cutout switch are to be wired.rds22
  13. C

    1964 40 hp johnson blown gasket

    will a blown intake gasket cause low compression and poor idle
  14. C

    question for paul moir

    could you look at these pics and tell me what year you think this is.40hp 60 something year<br /> http://community.webshots.com/user/cluke3
  15. C

    powerhead year new post

    can anyone tell what year this powerhead is <br /> http://community.webshots.com/user/cluke3
  16. C

    question 40 hp

    just bought a 40hp johnson or rude power head off e bay they said they think it is a 1964 there are no numbers on the welch plug. is there anyway to tell what year this is without the numbers. i need gaskets but dont know what year to order
  17. C

    1960 40 hp johnson rds22

    anyone know what year powerheads will work with this model . i bought a 40 hp powerhead owner said it was 1964 but no numbers on the welch plug by the thermostat like my old one. are thay somwhere else this one has a plug with a hump but no numbers.
  18. C

    1964 evinrude 40hp

    compression 60lb both cyls is this accecptable
  19. C

    1960 40 hp johnson rds22

    what direction would the armature base rotate to full spark advance i am trying to adjust the control rod collar to provide 1/32 clearance from the pivot pin I have the manual but cant figure it out.
Top