Search results

  1. F

    2002 Mercury 9.9 Carb issue

    Hello, I am working on a 2002 9.9 HP Merc 2-Stroke for my neighbor. The motor starts but jumps up to WOT even though It is not at WOT. I dont know anything about the carbs on this motor. looking in from the front of the carb there seems to be a needle jet that doesnt move and you can see gas...
  2. F

    1971 Johnson 100hp Timing

    Hello! I have a question about timing on this Johnson. I dont know that it is timed correctly and I just want to check it. Unfortunately I dont have a large enough test tank. I seen a post by Joe Reeves about timing without a tank or wheel simply by subtracting 4 Degrees on this post...
  3. F

    1971 johnson 100hp carb issues I think

    Hi Guys. I recently bought a used 1971 Johnson 100hp and found out that the carbs on the motor are not the stock carbs they are from a 125 hp motor. They do not have the slow speed adjustable needles that this motors carbs are originally equipped with and so it runs a little rich on the bottom...
  4. F

    1971 Johnson 100hp New to me.

    Hello Everyone. Well I bought the motor yesterday (1971 Johnson 100HP) to replace my blown 1971 Rude 60hp and I did a comp test while there at his shop. The readings are as follows From back of motor Top left 118 psi Bottom Left 118 psi Top Right 118-120 psi Bottom Right about 135psi I...
  5. F

    Buying a New to me motor What to look for

    Hello Again and thanks for all your help on that 1971 Evinrude 60HP I had which didnt pan out for me but I am going to purchase a new motor today. From what the seller tells me it is a 1971 Johnson 100HP V4. Supposedly it has sat for 20 Years in a warehouse before he got this motor. It had...
  6. F

    1971 Evinrude 60 hp Rebuild.

    Yup I wanted to take the boat out this weekend but there was that knock again I couldnt help but tear the motor down and find that Piston one with the low compression was melted pretty good. So I think I may rebuild. On the underside of the pistons there is the M logo which I think is Mallory...
  7. F

    1971 Evinrude 60 HP

    Ok I have an issue I havent encountered up until last night. I was assembling the new water pump housing and getting it ready to install on the LU. I was using a tap to clean out the threads as I usually do just for good practice and on the last hole the tap broke off inside.... Im not able to...
  8. F

    1971 Evinrude 60 HP Motor Knock

    Im not sure where to start with this as I haven't been able to put the boat in the water and test it to see if it knocks all the time or not or just in nuetral or whatever. I dont think this knock is normal. Here is a video what do you guys think? Should I tear the head off and check the...
  9. F

    1971 Evinrude 60 HP Water pump Issue

    So I had a sneaking suspicion that my water pump wasn't pumping. I have a few questions and a few pics that I'm Hoping someone can answer for me. This site is great lots of great knowledgeable people. I have already ordered from here and as it seems i will be ordering again. Probably a whole...
  10. F

    1971 Evinrude 60 HP Water pump Offset

    Is This normal? I cant remember where but I thought I read somewhere that the pump housings are offset from the driveshaft. Could someone let me know if this is actually normal?
  11. F

    1971 Evinrude 60HP Stuck in reverse

    Hello I hope someone can help me with this issue. although I believe I will have to take apart this lower end. I guess I might just need to hear it before I do it lol. I had this motor on the lake today to launch and keep in mind I did just buy this boat cheaply so I dont know much of the...
  12. F

    Steering Lock Nut

    Ok I have searched around but i cant find any info on my problem. The Lock Nut that attaches the steering cable to the tube at the rear of the boat will not thread back on to the tube.... I dont see any thread and it doesnt look as that there ever was any.... when I turn the wheel to the left...
  13. F

    1971 60 HP Evinrude Triumph Cooling Question

    Hi, I was hoping someone could help me to figure out if this was normal or if it is something I have to fix. I have hooked my Motor up to the Muffs Getting ready to put it in the water this Saturday! I noticed that Water was escaping from the spot cirlce on the pic. My question is if this is...
  14. F

    1970 Evinrude 60HP Triumph ID Tag Missing

    Hello Everyone, I'm hoping to get some help Identifying This Motor I have Pictures of it as well If needed. A Couple days ago I bought this boat 1973 Winner Marauder 17ft for a great price and I am looking to go over the engine to prep it for the summer. I wen to locate the ID Tag and it is...
Top