Search results

  1. pcmpete

    CCM:Lever1 error. HELP PLEASE

    I have twin Mercruiser 377 with DTS and Axius randomly I get the CCM:Lever1 error and cannot control my port engine with the DTS controls, but I still have control with the joystick. any ideas of where I need to start diagnostics? when I key off and on again the port engine functions as normal...
  2. pcmpete

    Where does the Mercruiser DTS system gets it power from?

    I have checked my Clean Power cable from the battery to the engine. Both read 14.52volts at idle. My alternators go thru an isolator and the output is 13.8volts But my Vessel View only shows 13.1volts (and never gets any higher) That is a difference of 1.4volts from the battery and 0.7volts from...
  3. pcmpete

    Mercruiser 377's with DTS & Axius - Battery Replacement options?

    I am looking at replacing the batteries this year. I have twin Mercruiser 377's with DTS & Axius. My Express Cruiser currently has 4 batteries total from 3 different manufacturers. (from Previous owner) The trays are set up for Group 27, but don't changing to Group 31 trays if needed. My onboard...
  4. pcmpete

    DTS 'Clean Power' cable - which battery?

    I have a DTS/Axius system and get different error messages, after research and help on this forum I cleaned all my battery connections, changed out my alternators. now the errors have reduced in frequency, but I still get only approx 13v showing on my Vessel View. After doing more research, I...
  5. pcmpete

    Voltage drop(s)

    I do have the Mercruiser DTS with Axius system, I don’t know how much load this puts on the system. I have only owned the boat for 4 months and still learning its setup and functions. Thanks
  6. pcmpete

    Voltage drop(s)

    I just replaced my two alternators trying to resolve a low voltage issue. My setup is as follows: 2 Mercruiser 377’s with 70amp alternators 2 starting batteries 1 house battery 1 generator starting battery. When I measure the voltage at idle rpm I get the following results: At alternator -...
  7. pcmpete

    TVM Fault Critical - Twin 377's B3 with DTS and AXIUS

    New alternators will be I stalled this week. I will report update
  8. pcmpete

    TVM Fault Critical - Twin 377's B3 with DTS and AXIUS

    Update. When running at idle my VV shows voltage less than 13v. I got it a throw the error alarm when I was cranking the engine, voltage dropped to 9v and that is when the alarm get off. video show idle and 1200rpm and the volt. starting batteries are Deka Group 27 lead acid with 800 MCA and...
  9. pcmpete

    TVM Fault Critical - Twin 377's B3 with DTS and AXIUS

    I will be back at the boat on Friday, i will test the batteries and alternators and video the vessel view voltage when the fault occurs.
  10. pcmpete

    TVM Fault Critical - Twin 377's B3 with DTS and AXIUS

    the port motor shows 12.1v
  11. pcmpete

    TVM Fault Critical - Twin 377's B3 with DTS and AXIUS

    I started getting this error, TVM Fault Critical, and sometimes my Starboard motor would just quit. After I silence the bells and alarms it starts right up again. Today I was trying to do dig deeper in the trouble i noticed my voltage at idle was ready 12.0v. Can any one point me the right...
  12. pcmpete

    Custom sun platform and rear seat building method query????

    I plan on making a custom sun platform/engine cover that is also the rear seat back rest. Is it impossible to make the frame/shape from 2x2 timber and stretch fleece over it and epoxy to create the shape, then build in strength with 3 or layers of 1708. What would be disadvantages to this...
  13. pcmpete

    Starter cable sizes?

    I am looking for info on what is the recommend size for replacement starter/battery cables? They are for a VP AQ130c and only 3ft in length. I cannot see/read any markings on the old cables. Thanks
  14. pcmpete

    5200 curing in dry desert heat???

    This time of year here in Phoenix AZ it get very warm and very dry. What is the best method to help 3m 5200 cure? Can I spray misted water twice a day over the 5200 to add moisture? thanks
  15. pcmpete

    Strap for old winch

    I am looking to replace the rope on my winch with a 2" strap. But the center of the winch hub has two holes to pass the rope thru and tie it off. There are no holes on the drum sides. What type of strap end do I need for this, or is a new winch on my shopping list? Thanks
  16. pcmpete

    AQ130c Restricting Jet?

    I needed to replace the breather hose from the crankcase to the carbs and noticed that there is a small plastic 'bushing type' item in there. I checked the volvo penta online store and this item is called a Restricting Jet . Item #29 in this...
  17. pcmpete

    Aq130c Rocker cover gasket torque and sealant...

    Can anyone tell me the correct torque for the rocker cover cork gasket torque and would it be a good or bad idea to use permatex sealant? Thanks all
  18. pcmpete

    Bearing spacer???

    I just got new bearings put into my hubs but there is approx 1/8" movement when the castle nut was fully tightened. The axle store I went to fully seated the races in the hubs. Can I safety put a spacer in the hub before the outer race to take the movement or just remove the races and not...
  19. pcmpete

    Hard to find bearings

    Hi all, I am refurbishing my old 1975 Vanson trailer. But I am having a very hard time finding replacement bearings. The number on the bearing is L60140. Does anyone know where to get this? I would hate to get a new axle and hubs just because I cannot find a bearing. Please help.......:confused:
  20. pcmpete

    Bunk adjustment

    I was doing some pre-season maintenance on my trailer and I noticed the bunks have shifted down and the keel in resting on the keel roller. Should the keel be sitting on the roller or the roller just a guide when loading/unloading the boat should rest solely on the bunks?Thanks
Top