Shop
Community
Home
Forums
New posts
Search forums
What's new
New posts
New media
New resources
Latest activity
Media
New media
New comments
Search media
Resources
Latest reviews
Search resources
Members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
New media
New resources
Latest activity
Menu
Log in
Register
Install the app
Install
Home
What's new
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Latest activity
What's new
New posts
Latest activity
L
Longarch
posted the thread
Successful Deletion of VST, Primer, & Fuel Pump
in
Johnson & Evinrude Outboards
.
To avoid the high cost and desperate searching for used parts, I've successfully replaced the Vapor Separator Tank (VST), Choke /...
Aug 27, 2026
Texasmark
replied to the thread
cupped prop question
.
.....and the peak of the torque curve is usually much lower than the max RPM point.....at least that's the way it is on 4 stroke diesels...
Aug 27, 2026
Texasmark
reacted to
alldodge's post
in the thread
cupped prop question
with
Like
.
There is always a give take between max RPM achievable and max RPM performance increase. Gaining that last 200 RPM may not gain any...
Aug 27, 2026
9
99yam40
replied to the thread
Sand getting into Suzuki 20hp outboard - can I pull it out?
.
you can also try blowing compressed air up the tell tail outlet, while running on muffs or in a tub to see if that changed the spray...
Aug 27, 2026
tpenfield
replied to the thread
White gelcoat restoration
.
There is a product called Re-Gel, which I believe is a 2-part product that cures like gelcoat. Basically a clear coat. There are some...
Aug 27, 2026
FLATHEAD
reacted to
Chris1956's post
in the thread
Deep pitting inside water jacket on power head.
with
Like
.
You can epoxy the pitted areas. If you clean the metal, wipe it with acetone and use Marine-Tex to fill the pits, it will add some time...
Aug 27, 2026
J
jlh3rd
replied to the thread
cupped prop question
.
it's in the range but I want to be at the max by myself.
Aug 27, 2026
S
Sandy-man
replied to the thread
1988 125 HP Force Rebuild
.
I think I just figured out what you mean by stickys. I found the sticky from Frank Acampora about syncing the car s and timing.
Aug 27, 2026
S
Sandy-man
reacted to
Scott Danforth's post
in the thread
1988 Bayliner Capri restoration, parts needed
with
Like
.
Bayliner bought from the lowest cost catalogs back in the day. Most of those companies have come and gone You will most likely need...
Aug 27, 2026
S
Sandy-man
reacted to
redneck joe's post
in the thread
1988 Bayliner Capri restoration, parts needed
with
Like
.
could you fab from oak wood? Try https://www.baylinerownersclub.org/ pretty uppity people so state your business and get out. They...
Aug 27, 2026
S
Sandy-man
reacted to
todhunter's post
in the thread
Fiberglass Hull Restoration
with
Like
.
Back from the dead!
Aug 27, 2026
S
Sandy-man
replied to the thread
1988 125 HP Force Rebuild
.
I don't know what you mean by "stickys".
Aug 27, 2026
J
jlh3rd
replied to the thread
cupped prop question
.
the 6000 rpm is at the max recommended range. I want that with me on board only. Now it's 5800. It's a pontoon. Not looking for more...
Aug 27, 2026
Scott Danforth
replied to the thread
2-4-C
.
Many dealers are struggling right now until you get into the range of boats that are resistant to financial climate changes. even great...
Aug 27, 2026
O
OnThePontoon89
replied to the thread
1989 3cyl 75 HP Evinrude - Running on One Cylinder? (Videos Included)
.
Ya I already did. Pic was before heat shrinking. Heat shrunk the ends and wrapped in electrical tape. Given electrical issues I...
Aug 27, 2026
Home
What's new
Top