WOT timing

bgbsshntr

Seaman Apprentice
Thread starter
Joined
Jan 2, 2016
Messages
33
This winter has been terrible for working on the boat. I have to do it outside. Here is were I am at. Last weekend was supposed to be the final wrap up of the motor, make sure he did carbs correct and time it. Friday the 13th hit me. Pulled the boat to the street and found out I had blown axle bearings. So I just pulled the carbs and took them to my friends house for clean and rebuild. Found the guy put wrong needles in two of the cabs (to long and the floats barely moved), explains oil fouling of two of my plugs. Had the trailer repaired this week, and going out to my friends house to finish it today. Timing, fuel filter and lower unit oil change. Wish me luck all, that this will finally have my 200 horses flying across the lakes. Thanks again for all the help everyone of you have given.
 

bgbsshntr

Seaman Apprentice
Thread starter
Joined
Jan 2, 2016
Messages
33
I want to thank all who have helped me on my motor. A special thanks to Mr. Joe Reeves, for his knowledge and patience. I know more about this motor than I ever expected or wanted to. From the top a piston detonated. Bought a rebuilt power head. Paid someone to install and get her running (1500.00). Things I found with help after he said it was done. Stator melted and made timer base stuck, the carbs he rebuilt had two over sized float needles, the fuel pump was weak. I have over time found everything that was wrong. The final thing was timing, and thank to Joe, it is spot on. It starts right up and I don't have to keep choking to keep it running and doesn't stall when I drop into gear. She jumps right up on plane, and starts with just a key bump when I am ready to move. Thank you all so very much.
1 very happy boat owner
 

Joe Reeves

Supreme Mariner
Joined
Feb 24, 2002
Messages
13,262
I can' find this timing procedure

(Timing At Cranking Speed 4°)
(J. Reeves)

NOTE: If your engine has the "Fast Start" feature", you must disconnect/eliminate that feature in order to use the following method. The "Fast Start" automatically advances the spark electronically when the engine first starts, dropping it to normal when the engine reaches a certain temperature.

The full spark advance can be adjusted at cranking speed,"without" have the engine running as follows.

To set the timing on that engine, have the s/plugs out, and have the throttle at full, set that timer base under the flywheel tight against the rubber stop on the end of the full spark timer advance stop screw (wire it against that stop if necessary).

Rig up a spark tester on the #1 cylinder plug wire. Hook up the timing light to the #1 plug wire. Crank the engine over and set the spark advance to 4° less than what the engine calls for.

It's a good idea to ground the other plug wires to avoid sparks that could ignite fuel that may shoot out of the plug holes. I've personally never grounded them out and have never encountered a problem but it could happen.

I don't know the full spark advance setting your engine calls for, but to pick a figure, say your engine calls for 28°, set the timing at 24°. The reasoning for the 4° difference is that when the engine is actually running, due to the nature of the solid state ignition components, the engine gains the extra 4°.

If you set the engine to its true setting at cranking speed, when running it will advance beyond its limit by 4° which will set up pre-ignition causing guaranteed piston damage! You don't want that to take place.

No need to be concerned about the idle timing as that will take care of itself. The main concern is the full advance setting.

A fellow member from one of the various marine forums suggested having water supplied to the water pump (flushette or barrel) simply to provide lubrication to impeller. A worthwhile suggestion I thought, and entered here.

Be sure to use your own engines spark advance settings, not the one I picked out of the air here in my notes.

********************
 
Top