help with prop

steamer454

Cadet
Thread starter
Joined
Mar 21, 2016
Messages
8
I have a 89 120 evinrude. I t is on a 16.5 cajun boat take for ever to get out of the hole. It only runs around 5000 rpms wot. Prop is a raker 13.5 x 24
I have a 13 x 21 aluminum I was gonna try. Any thoughts?
 

jbcurt00

Moderator
Staff member
Joined
Oct 25, 2011
Messages
25,353
Need to know if you are reaching ideal WOT RPMs w the prop you have now. That much down in pitch and diameter may be too much, you dont want to over rev the motor, unless you're over propped now..

Someone should stop by and give you the prop ranges and ideal WOT RPMs for your 120hp. Then you can fine tune prop selection.

Factors other then prop may be causing the boat to be slow to plane.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
You asked so here we go.---------Is the boat in good shape and not waterlogged ?---------Is the motor in good shape and producing it's rated power ?---Dropping pitch certainly brings the revs up and helps with acceleration.----In this case about 550 / 600 rpm.---But what if there is something wrong with the motor ?
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,701
Did it used to run at a higher RPM? You're at the bottom of your engine rpm range which is 5000 - 6000. Try the aluminium prop. The raker is a good prop, it does well if the motor is raised on the transom so the anti ventilation plate is 1 1/2 to 2 inches above the bottom of the boat. However I have no idea what a Cajun boat looks like. As I said, the Raker is a good prop, but maybe the one you have has too much pitch. Did it used to run at a higher RPM?
 

Faztbullet

Supreme Mariner
Joined
Mar 2, 2008
Messages
15,938
Raker is a good prop
This I will disagree with ...they are good if worked over a bit. I got a stock 24p that when you put it on boat it feels like you dropped a drift sock behind boat!! It wont lift,slow out of the hole and 8-900rpm off on top end. It been to 3 props shops and no one can figure out why!
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,701
Maybe your motor is tired, or you're trying to run too much pitch. The Raker does grip the water well and if your previous prop was slipping that certainly account for an rpm drop

I said the Raker is good, My Enertia is better
 

steamer454

Cadet
Thread starter
Joined
Mar 21, 2016
Messages
8
Ok I guess I should have given more info. I just bought this bass boat.Last owner 65 year old gentlemen. He owned it 3 yrs and never ran a full tank of oil out of it. Motor has good compression runs strong on top end just doesn't want to get out of the hole, motor actually seems to not have any low end power. I changed plugs they looked good. Just thought rake was too much for a 120.
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,701
it sounds a little too much based on the rpm you are getting. Based what rpm you're turning a prop in the 20 - 21 should be close to what you need. It will run a lot stronger if you get the rpms up
 
Last edited:

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
Current thinking on propping is that the ideal prop should let the engine run right up to redline. As was stated, that engine should run right up to 6000 rpm's with the correct prop on it. So, your current prop is running 1000 rpm's too slow. The raker is actually causing the engine to overload the engine-it has too much bite. The raker 24 has a lot of cup on it, so that stainless prop actually runs more like a 25 pitch. You are at least a couple of prop sizes too high in pitch. Absolutely try the 21. If it lets the engine run right up to 6000 rpm's it's the ideal prop.
 

steamer454

Cadet
Thread starter
Joined
Mar 21, 2016
Messages
8
Ok I changed prop went to the lake. Came up really fast motor sounds good to many rpms.I stopped to fish a little. Left channel and it did not want to come out of the water. So now I have a issue. Runs good on high end. Previous owner had it two yrs and only used it 4 or 5 times sat most of the time.
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
What do you consider as "too many rpm's?" When you restarted to come up on plane, do you know if you had all 4 plugs firing? After running for a while and you shut the engine down, it will continue to heat up-since no more cooling water is going thru the block. When it gets superheated for this brief time, it can affect weak ignition components, causing a misfire. May run just great tomorrow when you start it up cold.
 

steamer454

Cadet
Thread starter
Joined
Mar 21, 2016
Messages
8
I believe its an electrical problem, only because its intermittent. Runs fine after it comes out of the hole, so whatever it needs on the low end is acting up. I thought maybe jets but believe that would not come and go. could be power pack or trigger switch, as a maintenance tech hard to find problem that I cant simulate.
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,701
Well check the wires that move as the throttle is moved
 
Top