Evinrude optimum performance question

Gary Chappie

Recruit
Thread starter
Joined
May 8, 2003
Messages
1
I recently purchased this boat and it runs excellent but the helicopter mechanic in me is constantly wondering if it’s operating at its best. Here are some specifics and my question to you pro’s…is this as good as it gets.<br /><br />BOAT – Wellcraft 190 CCF<br />ENGINE – Evinrude 112 SPL (no hydrofoil at this time) runs fantastic.<br />LOAD – Two adults and required equipment<br />PROP – 13 3/8 X 17 (cupped and appears to be stainless but do not know make)<br />WOT RPM – 5200<br />SPEED @ WOT (GPS) – 35 – 36 mph<br />GAS – 87 octane <br />OIL – Pennzoil synthetic blend<br />COMPRESSION - ?? Still must purchase kit<br /><br />I know other folks have some big problems out there and do not want to clutter this excellent forum with this kind of question but its something I have to know so i can put it out of my mind. Can it be better???<br /><br />Thanks for you time.
 

JB

Honorary Moderator Emeritus
Joined
Mar 25, 2001
Messages
45,907
Re: Evinrude optimum performance question

You could stand more WOT rpm, Chapppie. 5500 is about right for that engine.<br /><br />I would try an uncupped 17" prop and if I couldn't get 5500rpm I would go to a 15" cupped prop.<br /><br />Good luck. :)
 

Chappie

Cadet
Joined
May 8, 2003
Messages
22
Re: Evinrude optimum performance question

Thanks JB, I will do just that. Question - I called several marine stores (national chain) and they do not have test props. Since I don't have a bottomless pocket, is there a resource (i.e. marinas, prop stores??) that would have a set of test props that I could borrow/rent until the optimum WOT rpm is achieved, then purchase the correct one??
 

Chappie

Cadet
Joined
May 8, 2003
Messages
22
Re: Evinrude optimum performance question

I just noticed that i have two logins.......how do i get rid of one of these?? I checked the "FAQ's and did not find how. Thanks
 

Dhadley

Supreme Mariner
Joined
Feb 4, 2001
Messages
16,978
Re: Evinrude optimum performance question

Your target rpm is 5800 with an average load. Try raising the motor on the transom (increase the X dimension) before you spend any money. The less unit you have in the water, the less drag which should increase your top rpm's.<br /><br />When buying a prop try to work with a performance center. They will arrange a test session and have several props to try and can make recommendations based off of testing. We do anyway.<br /><br />Everything else looks great! It may be a good idea to do a decarb job. There are lots of excellent posts here about that.<br /><br />Good luck!
 

Chappie

Cadet
Joined
May 8, 2003
Messages
22
Re: Evinrude optimum performance question

DHadley,<br /><br />Thank you for your input. I run the OMC de-carb in the fuel and also performed a de-carb (engine tuner) a few weeks ago. Did not notice much difference as others have posted before.<br /><br />About the x dimension - When I bought the boat, it had a hydrofoil on the cavitation plate but it was in sad shape and eventually broke off. I removed the base of the hydrofoil(s) from the cavitation plate and have not yet made a decision of purchasing another. I did notice that the boat won't plane as easily and I don't have that great of a hole shot. I also noticed that when the hydrofoil was on , the prop would cavitate (even trimmed down) badly in turns (high and low speed). Not sure if you are familiar with this boat but the engine is mounted in the second holes from the top and the cavitation plate is even with the bottom of the transom. With this new information, what would your recommendations be?? <br /><br />Thanks for your time.
 

Dhadley

Supreme Mariner
Joined
Feb 4, 2001
Messages
16,978
Re: Evinrude optimum performance question

Sounds like the prop is starting to lose the "bite" (ability to grab the water). Probably lost a little diameter as well as cup length. <br /><br />It might not hurt to send it to a prop shop to get it reconditioned. Even if you get another prop that will make a good spare.<br /><br />Keep us informed!
 
Top