Evinrude 5HP Angler questions

TroutbumShawn

Cadet
Thread starter
Joined
May 28, 2016
Messages
16
No Title

Ok, I've replaced everything and still no go. I set the points at 0.020 at the mark in the photo which appears to be the high spot. Is that right?
​
 

Attachments

  • photo245380.JPG
    photo245380.JPG
    57.3 KB · Views: 0

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
The black wire must tucked in close to the coil so that flywheel does not rub on it.-----Did you remove magneto plate to install wires into the coils ?
 

TroutbumShawn

Cadet
Thread starter
Joined
May 28, 2016
Messages
16
Yes I took the plate off, trimmed off about 1/4" of coil wire to get fresh meat. Reinstalled. Wires are tucked away well. The bottom wire on this coil is green and I put it on the points screw with the condenser wire, the black wire is on top and isn't long enough to go to the points so I put it under the screw that holds the coil to the plate (the old coil was red bottom, green to if I remember correctly). Turned the crank clockwise and set the gap at the position indicated in the picture. I set them slightly early in the mark as they are new points to allow for wear in. I cleaned the points using the paper method and then cleaned up the magnet on flywheel a bit. She seems to have good spark although I am still unsure if the mark is the correct spot. Im thinking I may have a fuel issue now. I know fuel is getting to the pump and when I remove to out line from the pump shell squirt fuel when the motor is cranked. I've pulled the plugs and they seem drier than I would expect after that much cranking. Could I have a piece of rust from the old tank plugging a jet or something? The right carb nut looks unaccessible unless I remove the pull cord assembly?
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
That nut is easily removed with a small screwdriver and hammer.---Done that for years with no problems.----Will save a novice a whole bunch of frustration too.
 

TroutbumShawn

Cadet
Thread starter
Joined
May 28, 2016
Messages
16
Thanks, I'd really like to get this thing going so I can take Dad out fishing for Father's Day.
Anyone know of a good video or tutorial on cleaning this carb? Looks basic enough, but they always do first time..... until you screw something up :^(
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
That carburetor nut is easy to remove if you aren't so scared. All you have to do is remove the two screws from the top of the starter and lift it up just enough to release it from the bottom bearing, and tilt it aside. It will not go sproing-kaflooey. Now you can remove the carburetor. The high speed jet is probably plugged up.
 

TroutbumShawn

Cadet
Thread starter
Joined
May 28, 2016
Messages
16
Ok, making progress....I had the carburetor off and took it all apart cleaned everything up and soaked it in carb cleaner. It didn't appear as dirty as I expected. All the offices seem clear including the high speed. The only thing I noticed was that the float valve stuck up in the body sometimes when tickling the float. Reassembled everything and pulled for awhile with a couple farts. I hooked my drill up on flywheel nut and spun her for a little while and it started up. Didn't seem to want to rev out much (in my opinion) but ran ok till I tried idling down. I tinkered with the low speed needle a bit (when I installed it I turned till seat then backed out 3/4 to1 turn). It would not start from pull cord so I again used my drill and it started. Would run for a couple minutes then slowly idle down until it eventually would stall. There was fuel in the line, albeit with some air bubbles. Any ideas?
 

TroutbumShawn

Cadet
Thread starter
Joined
May 28, 2016
Messages
16
No Title

Went at her again today, same results. I pulled the valve out of the motor and my spare motor and they are completely different (see picture, the bigger one is the original, tiny one is out of the spare motor I bought)? Tried the spare in my main motor and got same results, with some difficulty I get her started then it runs for a bit and slowly revs come down till it dies. Then it won't start again. I've tried squeezing the fuel build a bit when it starts to die down and tried turning the low speed in and out with no success. Could my timing be off or do you think its fuel?
 

Attachments

  • photo246242.jpg
    photo246242.jpg
    233.5 KB · Views: 0
Top