Design of PVA circuit

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Ok, serve me up a slice of that humble pie, I was wrong. Household voltage is about 168 peak Volts positive followed by 168 peak Volts negative. Since the diode only allows half wave through (168 Volts), that is what your DVA should be showing.

Unless we need to bring n some more pie.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Just confirming, you do have your voltmeter set on a DC Volts scale, right? Because you are reading the stored DC Voltage across the capacitor.

Also, I think somewhere you wrote that you used an electrolytic cap. That might not be a good idea.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
I was just thinking of possible internal leakage bleeding off the charge.
 

Hughjohnson

Seaman
Thread starter
Joined
Jul 16, 2011
Messages
53
thank you everyone
I am left with the conclusion that the Peak Voltage Circuit I have built with various components is in fact giving me half wave rectification and showing the DC voltage of 60 which is half of the RMS of 120 AC.
Crosby to answer your question. the AC voltage on my charge coil was 120 v and the DCA adaptor showed 27 v DC.
however the ratio on my power coil is 46 v AC to 30 v DC . I expect the power coil is sinusoidal and the charge coil a pulse. this might account for the difference.
Now i am still left with the problem that my manual calls for a Peak Voltage Adapter and talks about peak voltage not RMS or DC .
I am calling DCI electronics to see if they might know . they make the ignition systems.
thanks again
Hugh
 

bruceb58

Honorary Supreme Mariner
Joined
Mar 5, 2006
Messages
30,834
I am left with the conclusion that the Peak Voltage Circuit I have built with various components is in fact giving me half wave rectification and showing the DC voltage of 60 which is half of the RMS of 120 AC.
No it isn't. The circuit is designed to store voltage peaks! It doesn't care if its a sinusoid or pulses. It does no averaging.

It is not a rectifier...it has a diode so that the voltage stored across the cap is not dissipated when the voltage drops. The only element that drops the voltage across the cap is the very large bleed resistor. The peak voltage that the circuit sees is stored by the cap and hence the reason you use the DC reading of your multimeter to measure it.

Ignore any comments from anyone who mentions RMS.
 
Last edited:

Hughjohnson

Seaman
Thread starter
Joined
Jul 16, 2011
Messages
53
OH Boy
well we all seem to agree that the peak to peak is 340 which is 170 each way . I think we also agree that this circuit should be measuring peak and that is what the capacitor is supposed to do .catch the peak and hold it cos there is now way for the electrons to go except very slowly through the I megohm resistor.
But it aiint working that way.
I am going to try 22 micro farad ceramic capacitor when I find one instead to the 100 mF electrolytic and the 2200 pico farad Ceramic.
thanks again
FR yes I had the meter on DC volts but good point we all make silly mistakes
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Ok guys, I finally did what I should have done long ago. I dug out the DVA adapter I cobbled together a couple of years ago and only used once. I used a 1N4007 1A, 1000V diode and a 0.2mfd 400V orange drop capacitor. I didn't even use a bleeder resistor, reasoning it really isn't needed since I'm using an old school analog multimeter.

So...I plugged it into the house AC outlet, and guess what I got? A hair over 160 Volts DC across the capacitor. Just about what we expected.
 

Hughjohnson

Seaman
Thread starter
Joined
Jul 16, 2011
Messages
53
thank you F-R Supreme Mariner
Fantastic. And today I bought a 22 micro farad 400v electrolytic and connected it up and GUESS WHAT !65volts DC across the capacitor.
Thank you all for your patience and inputs. My problem was one faulty electrolytic cap and the other was far too small as one of you pointed out to me.
Cheers and now I can start testing my ignition system again
Hugh
 

bruceb58

Honorary Supreme Mariner
Joined
Mar 5, 2006
Messages
30,834
I didn't have access to a calculator the other day and couldn't do the math in my head but the 2200pF would be fine if the multimeter you are using has around a 1 KHz sampling rate. If it's slower then you wouldn't get accurate numbers.
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Ok guys, I finally did what I should have done long ago. I dug out the DVA adapter I cobbled together a couple of years ago and only used once. I used a 1N4007 1A, 1000V diode and a 0.2mfd 400V orange drop capacitor. I didn't even use a bleeder resistor, reasoning it really isn't needed since I'm using an old school analog multimeter.

So...I plugged it into the house AC outlet, and guess what I got? A hair over 160 Volts DC across the capacitor. Just about what we expected.


Interesting update, I left the setup laying on the table overnite and plugged it in again this morning without touching it. The voltage now reads between 165 and 170 Volts. Just goes to show that line voltage varies a bit.
 

gm280

Supreme Mariner
Joined
Jun 26, 2011
Messages
14,605
Not that I really needed one, but I built one a few days ago now, just for the heck of it. I used a 1N5407 diode (3 amp 800 volt), only because I had it, and a 2.0 mfd 450 volt cap and of course the typical 1 meg ohm 1/4 watt bleed off resistor. And after building it, I plugged it into my wall receptacle and ~160 plus volts appeared on my digital Fluke meter. So I am not so sure the size of the cap really maters if you get one large enough to hold the peak voltage until the meter can sample it. So seems the circuit is quite easy to duplicate and since every part was laying around in my shop, it cost me nothing. Just thought you would like to know. JMHO

Yea I could put my O'scope on it, but really, why? It isn't that serious. It works and will help trouble shoot such issues if I ever need it. Who knows?
 
Top