Carbing a 79 150 Johnson block

Bigkrypto

Cadet
Thread starter
Joined
Apr 6, 2014
Messages
10
Here's what I got so far it's a 79 150 block with 84' 175hp carbs
it cooled starts fine with some primes and idles . I can take off smooth and plane out nice . I top out 39 at 4500 rpm . I don't have a lot of torque tho when I take of 3rd throttle it bogs and I have to just take off smooth and I noticed when traveling I come down on back side of wave I bogs a little bit the main notice is when I try to load it on trailer I can't get past 1/4 throttle without it bogging out but if I prime the motor via primer motor it gets some balls and pushes it on up on to trailer quite impressively I might say.
So what should I look at doing carb replacing, messing with jets, not sure because of the mixed years and what jetting
 

Attachments

  • image.jpeg
    image.jpeg
    107.6 KB · Views: 0
  • image.jpeg
    image.jpeg
    95.5 KB · Views: 0
  • image.jpeg
    image.jpeg
    89.9 KB · Views: 0
  • image.jpeg
    image.jpeg
    78.9 KB · Views: 0
  • image.jpeg
    image.jpeg
    81.2 KB · Views: 0
  • image.png
    image.png
    1.3 MB · Views: 0

Faztbullet

Supreme Mariner
Joined
Mar 2, 2008
Messages
15,938
Need to make sure all the carb mounting nuts are in place and tight as I see one missing in picture. Also what size are the carbs as it will be stamped below the throats as if later big bore(3.625) carbs be hard to jet. From what you describing is a low fuel pressure/fuel level causing a lean mixture as primer richens mixture. Check float level and rebuild/replace both fuel pumps...
 

emdsapmgr

Supreme Mariner
Joined
Dec 9, 2005
Messages
11,551
Since you say you have a set of 175 carbs, they should have 1 5/16" throats. The jetting on these carbs are just slightly over the 150 jet sizes. You should be able to run with these carbs and jets right out of the box. I, for some reason, you are actually running 1 3/8" carbs, I could understand the running problems you are having-just too much fuel and air for your small bore block. You need to verify just what 175 carbs you say you have. In 1984 OMC did not make a 175. It was a de-tuned 200, which was sold at a 185 with 1 5/16" carbs, but with even larger jets.
 

Chinewalker

Fleet Admiral
Joined
Aug 19, 2001
Messages
8,902
Also, 4500 revs is low. Might be carb related and might sort itself out once you get the carbs nailed down. However, if you're still peaking that low once the mechanical issues are sorted out, you might need to go down in pitch to bring the RPM up, somewhere in the 5500 range.
 

Bigkrypto

Cadet
Thread starter
Joined
Apr 6, 2014
Messages
10
No Title

I'm finding out they are carbs from a 85 2.6 and had a bigger bore the my 79 150 so I'm thinking it's getting to much air and not enough fuel to make up for carb size . But would like to see if anybody has messed with jetting these . This motor runs pretty good and I was wondering even if it runs pretty good how could I tell if it's to lean.the carbs are 1 1/4".
 

Attachments

  • photo251981.jpg
    photo251981.jpg
    78.9 KB · Views: 0
  • photo251985.png
    photo251985.png
    1.3 MB · Views: 0
Top