Can't start a 70' 60HP Johnson in water?

justwannaboat

Recruit
Thread starter
Joined
Jul 20, 2003
Messages
2
(New boater - New Poster - Not that mechanically inclined but learning)<br /><br />I bought a used boat with a 1970 60HP 3 Cyl Johnson with a pushbutton shifter (Evinrude?) and a manual choke.<br /><br />I had it serviced before I even started it (New Battery, Battery Cables, Rotor, Spark Plugs, Clean and Tune Carbs, Replaced Impeller)<br /><br />When I picked it up I started it with the mechanic (Prime Gas Bulb, Neutral, Choke all the way in for first turn of ignition, Then pull choke all the way out)and it started and ran great.<br /><br />The next weekend I started it again in my driveway (With Rabbit ears) following the above process and it started right up.<br /><br />Here is the problem - when I went to the lake and launched it it would not start in the water. (It cranks but just will not start) I pulled it out, took it home and it started. I brought it back to the lake and it would not start again!<br /><br />Everyone I speak to is dumbfounded.<br /><br />The prop does turn when starting, but stops once started (I read an earlier post that said this was normal in a pushbutton shifter?) <br /><br />Someone thought either it is actually in gear, even though the neutral button is pushed, or submerging it in the water is creating a short in the shifter so the motor won't start because it thinks it is gear?<br /><br />Any Ideas - Running out of summer in NH!
 

Walker

Captain
Joined
Jun 15, 2002
Messages
3,085
Re: Can't start a 70' 60HP Johnson in water?

That shouldn't make any difference. The only thing the ignition knows is the neutral safety switch which is in the control box and only prevents the starter from working. It does not prevent ignition spark. This may sound far fetched but start it up again on ears and make sure that there is free exhaust flow through the prop. Go back to the lake and just back the boat in far enough to get water just above the cavitation plate. Try starting now. I'm thinking you might have too much exhaust back pressure. Also make sure your choke butterflies are fully closing when you put the choke on.
 

OBJ

Supreme Mariner
Joined
Dec 27, 2002
Messages
10,161
Re: Can't start a 70' 60HP Johnson in water?

Walker/justwanna.....think maybe there's a chance that the mech doing the work didn't make the sync and links and low end timeing with the lower unit in a test tank????
 

Walker

Captain
Joined
Jun 15, 2002
Messages
3,085
Re: Can't start a 70' 60HP Johnson in water?

OBJ, I had the same problem with my 94 120 and after doing all kinds of tuning on it I discovered that my choke solenoid was only working half-a$$. Fixed it and she fires up good now.
 

justwannaboat

Recruit
Thread starter
Joined
Jul 20, 2003
Messages
2
Re: Can't start a 70' 60HP Johnson in water?

Thanks guys. It's been raining the last few days but I will try to put it in the lake on night this week. (The mech at the shop said he ran it in the tank but I was not there then - I only saw it run with the rabbits) Will let you know how I make out.<br /><br />It does seem to have a free flow of exhaust in the driveway but being new to boat motors I cannot tell if the flow is normal?<br /><br />P.S. I did try the choke and the butterflies do close all the way?
 

OBJ

Supreme Mariner
Joined
Dec 27, 2002
Messages
10,161
Re: Can't start a 70' 60HP Johnson in water?

Justwanna....if your next trip produces the same results, I would do a compression test to determine if all cylinders are in good shape. Did the mech do this at the shop? The choke butterflies should close completely when choked and open fully when not choked.
 
Joined
Jun 4, 2003
Messages
20
Re: Can't start a 70' 60HP Johnson in water?

justwanna, <br />I've got a '71 Evinrude 65HP w/electric shift and it did the exact same thing to me. I would start at home, but once I got to the ramp it would not start. <br /><br />I've been going strong now for a couple of months....seems my problem was that the needles in the carbs was sticking. I re-built carbs, new needles, float, etc. Once this was done.....ran like a new one.
 
Top