62 Johnson 75hp Super Seahorse won't shift forward

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
Thanks for the replies. I haven’t dropped the LU yet. The electrical readings are ok on the coils so I have no suspicions on the cables. Racerone, you said earlier that the oil doesn’t matter. I want to try and get some satisfaction from the guy I bought it from. It is reasonable to assume this was not working properly when I bought it? He said everything functioned perfectly and would take it back if I wasn’t happy. I want to keep it. The motor runs beautifully. But I don’t want to go after him if I might have damaged it with the wrong oil. I’ve read so many posts saying you HAVE TO have Type C oil.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
For the testing that you are doing it does not matter !!!----Full of peanut oil / type C premium blend / # 90 gear oil / or empty it will lock up with 12 volts to green wire and you turning the prop counter clock wise.----I could repair your unit without a glance at a manual !----I could repair it without having to buy any parts as I have it all used in good condition !
 

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
You didn’t really answer my question. As I stated In my first post, I am new to this. If you are one of those guys that has no patience for newbies then please don’t bother. I’m looking for help, I’m not looking to annoy anyone. I’ll go somewhere else.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
I clearly stated that for the purpose of testing the oil does NOT MATTER !
 

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
My question was not about testing. You are not reading very carefully. Stop with the CAPS. Stop with the exclamation points. I’m not an idiot. You’re really taking all the fun out of this. Just forget it, man.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
If you had the spring and hub in your hands the assembly would lock up by pulling on the spring with your fingers.-----Bone dry with no oil on the parts.-----Sorry , I can not help it if you are unaware of how the system works.
 

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
Thanks for your help. I appreciate it.The reason I am here is because I am unaware of how the system works.
 

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
Thanks Jimmbo, I already solve one problem flipping through that manual- in the midst of this troubleshooting, I ended up in a “no-crank” state, dead ignition switch. I saw in the manual that the auxiliary start throttle has the safety switch and by easing back on the that throttle...all the sudden I have ignition! Brilliant. Knowledge is a powerful thing. Thank you.
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
Not quite sure what you are describing, but control boxes typically have a neutral safety switch. If it's out of alignment, the remedy is sometimes rocking the lever back and forth a little while in the neutral detent, while attempting to start with the keyswitch. The neutral safety switch is meant to interrupt the starter circuit if not in neutral (starter won't engage).

A kill switch (man overboard switch) on older outboards shorts ignition -- engine will crank, but won't start if the kill switch is engaged.
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
??-----Don't think you will find a neutral safety switch INSIDE the 1962 control box !
 

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
“In the event the electric starter does not operate when the engine is placed in fast idle position, hold the starter key in “start” position and gradually retard the throttle (RDS) or auxiliary throttle (RK). Should the engine start only after the throttle has been retarded slightly, the safety switch setting should be re-adjusted.”
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
The safety switch is on the distributor on the 75 hp electramatic and not in the control box !! -----It is found under the magneto plate on the RK and RD 40 hp models !
 

oldboat1

Fleet Admiral
Joined
Apr 3, 2002
Messages
9,612
I've sometimes lived with them a little out of adjustment, and just took it into account with my starting procedure. "By the book," though, should go in and adjust it.
 

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
So, I’m thinking the switch is intermittent because without adjusting anything, starter is operating normally. The only thing I did was move the starting throttle up and down.
 

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
If the safety switch is functioning properly, does it allow starting in gear? Mine will crank in any position. Does the safety switch prevent starting at a high throttle setting?
 

boobie

Supreme Mariner
Joined
Nov 5, 2009
Messages
20,826
Racer, you have to remember that all of the posters on here were not working on these motors back in 1965 like we were. Be patient.!!
 

racerone

Honorary Supreme Mariner
Joined
Dec 28, 2013
Messages
40,028
The safety switch prevents starting at too much throttle !----Motor will start in gear.-----Perhaps folks in the 60's were more aware of their surroundings and knew how to start motors.
 

Altstuder

Cadet
Thread starter
Joined
Jul 29, 2018
Messages
23
So, what you meant to say is yes- yes, the safety switch prevents starting with too much throttle. Racerone, the folks back in 60s were the best- hands down- they gave birth to me. Thanks for confirming my thoughts on the safety switch.
 
Top