1974 50 hp Evinrude 50473M hot sensor

txskcusmc

Cadet
Thread starter
Joined
Oct 3, 2016
Messages
6
Well I am having all kinds of problems with this motor. Last year I took the boat out and it ran fine all day until I was headed back to the ramp and then the hot sensor came on, I then turned the motor off and trolled the rest of the way to the ramp. Life is life and did not mess with the boat until about a month ago and after changing all kinds of parts, I still have the same problem. I have changed the thermostat, thermostat gasket, pressure relief valve and spring, water pump, impeller, power pack, coils, spark plugs and completely rebuilt the carb and now the hot sensor is coming on after it runs for about five minutes with the muffs on it. I really have no idea what else it could be that might be causing the sensor to sound. I am not scared to try something else just tired of putting money into this thing. All help is appreciated.
 

James R

Commander
Joined
Feb 1, 2007
Messages
2,681
Is the motor in fact running hot? You should be able to hold your hand on the cylinder head without screaming. Common temp around 120-130. If above 150 it could have a problem. Of course if it has been in salt water then thats a beast of another color.
 

txskcusmc

Cadet
Thread starter
Joined
Oct 3, 2016
Messages
6
I will check the temp of the motor this weekend and let y'all know

Is there a way to check the sensor ??
 

boobie

Supreme Mariner
Joined
Nov 5, 2009
Messages
20,826
There's a procedure in the factory service manual on how to check it.
 

txskcusmc

Cadet
Thread starter
Joined
Oct 3, 2016
Messages
6
I do not have one of those. Can you tell me how to do that procedure
 

txskcusmc

Cadet
Thread starter
Joined
Oct 3, 2016
Messages
6
Well I checked the temp on each head and it is getting up to 210 and that's when the sensor comes on don't know really what to do from here I have replaced everything that I can think of is there anything else that y'all might know.
 

boobie

Supreme Mariner
Joined
Nov 5, 2009
Messages
20,826
How did you check the temp on the head ?? EACH head on a 50 hp ??
 
Last edited:

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Why on earth did you change all that stuff (power pack, etc)? Well, never mind, in the first place you cannot test a water pump by running on muffs. So you don't know if you have a problem or not. The temp sensor is working if it is sounding the alarm. I suppose it is possible to go off at too low a temp, but that would be rare. Testing the sensor requires removing it. If you are going to do that, you might as well put a new one in.

EDIT: Um, back to the first time the horn came on, how hot was it? Was it smoking hot? If it was, you have more work to do. At a very minimum, a new head gasket and all exhaust gaskets. And while in there, check for scored pistons.
 

txskcusmc

Cadet
Thread starter
Joined
Oct 3, 2016
Messages
6
F_R. The first time the alarm went off I was running down the river and have no idea how hot it actually got but there was no smoke. As soon as it went off I shut the motor down. As far as all the items I replaced most where because the motor had been sitting for a while when I bought it. The power pack was because I took it to a shop because it wouldn't start

I used an infared temp gun when it was running. It took about ten minutes for the alarm to sound. I placed the temp gun on each head and took a reading and the average temp was 210 after ten minutes. The alarm can on just before I took that reading .
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
Well, I don't know what to tell you except get the boat in the water where it belongs and see if you actually have a problem.

AND, we are still confused about "each head". A 50hp only has one head.

If it is overheating with a new pump installed correctly, there must be a blockage or circulation problem. Impossible to diagnose from a distance.
 
Top