1969 Johnson 55hp

Icecube3456

Cadet
Thread starter
Joined
Aug 7, 2017
Messages
10
Having a problem getting our 55hp going into gear. It idles fine, but when put into gear it dies. Have new plugs, plug wires, carbs clean, and all the other easy stuff. Don't have a tachometer or compression meter. Have good spark. Plugs slightly wet with some smoke. Recently gapped points to 0.01 on all lobes. When we did get it into gear it had very little power. Probably under 10mph at WOT. Needle valves seem to be worn. The ends are slightly flattened on one side.
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,699
Spark to all cylinders? Until you know you have good compression... but you were messing with the points and that will require the timing be checked. Carbs may need cleaning(real cleaning, not spraying solvent down the throat). Carb to timing sync will also need checking.
 

Icecube3456

Cadet
Thread starter
Joined
Aug 7, 2017
Messages
10
Spark is good on all cylinders. I pulled the carbs and they are all good. This problem happened before I messed with the points. I checked the points because of the problems. So, timing could be a problem now but the other problems existed before I touched the points.
 

jimmbo

Supreme Mariner
Joined
May 24, 2004
Messages
14,699
When you had the flywheel off, what condition was the seal on the crankshaft in? Nice and dry or oily?
 

F_R

Honorary Supreme Mariner
Joined
Jul 7, 2006
Messages
28,226
First things first. Check the compression. It would appear that it is not running on all 3 cylinders. A damaged cylinder certainly would show up that way,
 

Icecube3456

Cadet
Thread starter
Joined
Aug 7, 2017
Messages
10
Everything under the flywheel looked decent but there was oil under the points. I can't check compression at the moment. I don't have access to anything to check it with until at least Saturday
 

Joeda4rh

Recruit
Joined
Aug 7, 2017
Messages
1
Sorry. Question from a different post you were in F_R. You said that you make a tool for removing and replacing the o-rings in an Evinrude or johnson air/fuel connector. Email me the cost and eta to Wisconsin please. Thanks. Jheckenbach@outlook.com.
 

Joe Reeves

Supreme Mariner
Joined
Feb 24, 2002
Messages
13,262
1969 55hp Johnson.... Don't have a tachometer or compression meter.... Have good spark.... Recently gaped points to 0.01 on all lobes.... Needle valves seem to be worn. The ends are slightly flattened on one side.

What spark plugs are you using.... make, heat designation, gap?

Compression gauges are fairly cheap. If you plan to be in boating for awhile, purchase one... you'll need it frequently. What is the psi reading of the individual cylinders?

Good spark doesn't really tell us very much. On that model, the spark must jump a 1/4 gap with a strong blue lightning like flame... a real SNAP! Does it?

The needle valves regulate the fuel flow on the low rpm/idle end of the engines rpm range, to be adjusted as follows. The damage needle tip is due to the forward nylon bearing/bushing being missing which allows the forward end of the needle valve to vibrate. Bushing is part #314166. Sometimes the damage tip can be restored by having the needle gripped in a high speed drill and holding a very good file against the damaged taper. The slightest imperfection of the taper makes it near impossible to obtain a decent idle.

(Carburetor Adjustment - Single S/S Adjustable Needle Valve)
(J. Reeves)

Initial setting is: Slow speed = seat gently, then open 1-1/2 turns.

Start engine and set the rpms to where it just stays running. In segments of 1/8 turns, start to turn the S/S needle valve in. Wait a few seconds for the engine to respond. As you turn the valve in, the rpms will increase. Lower the rpms again to where the engine will just stay running.

Eventually you'll hit the point where the engine wants to die out or it will spit back (sounds like a mild backfire). At that point, back out the valve 1/4 turn. Within that 1/4 turn, you'll find the smoothest slow speed setting.

Note 1: As a final double check setting of the slow speed valve(s), if the engine has more than one carburetor, do not attempt to gradually adjust all of the valves/carburetors at the same time. Do one at a time until you hit the above response (die out or spit back), then go on to the next valve/carburetor. It may be necessary to back out "all" of the slow speed adjustable needle valves 1/8 turn before doing this final adjustment due to the fact that one of the valves might be initially set ever so slightly lean.

Note 2: If the engine should be a three (3) cylinder engine with three (3) carburetors, start the adjustment sequence with the center carburetor.

When you have finished the above adjustment, you will have no reason to move them again unless the carburetor fouls/gums up from sitting, in which case you would be required to remove, clean, and rebuild the carburetor anyway.
********************
To be sure we're on the same page here..............
(Point Setting Of Battery Capacitance Discharge)
( Ignition Models - 1968 thru 1972)
(Some have points - Some do not)
(Joe Reeves)

The points must be set to .010 but no wider than .010..... BUT in some instances due to a possible slight inaccurately machined crankshaft lobe or a slight offset of one set of points, a setting slightly less than .010 would be required as follows.

Whether the crankshaft has two or three lobes, when setting the points, check the setting of the points on each individual lobe by rotating the crankshaft by hand.

You may find that setting one set of points to .010 on one lobe, then turning the crankshaft to the next lobe, the gap measures .011 or .012 (too wide). This is where you would need to close that gap down to the required .010. A gap too wide can result in a ignition miss when throttle is applied.

Bottom line, pertaining to the point setting at the various lobe locations____ .010, .010, .009, is okay____ .010, .010, .011 is not!
********************
(Spark Tester - Home Made)
(J. Reeves)

You can use a medium size philips screwdriver (#2 I believe) inserted into the spark plug boot spring connector, then hold the screwdriver shank approximately 7/16" away from the block to check the spark or build the following:

A spark tester can be made with a piece of 1x4 or 1x6, drive a few finishing nails through it, then bend the pointed ends at a right angle. You can then adjust the gap by simply twisting the nail(s). Solder a spark plug wire to one which you can connect to the spark plug boots, and a ground wire of some kind to the other to connect to the powerhead somewhere. Use small alligator clips on the other end of the wires to connect to ground and to the spark plug connector that exists inside of the rubber plug boot.

Using the above, one could easily build a spark tester whereas they could connect 2, 4, 6, or 8 cylinders all at one time. The ground nail being straight up, the others being bent, aimed at the ground nail. A typical 4 cylinder tester follows:

..........X1..........X2

.................X..(grd)

..........X3..........X4
 

Icecube3456

Cadet
Thread starter
Joined
Aug 7, 2017
Messages
10
I can't do a compression test until Saturday. I tested the voltage on the coil primary side with a homemade peak voltage detector. It was 194.9 and I've read that it should be around 200v. The coil primary windings have around 0.2 ohms resistance. Secondary side has about 270 ohms. So, the coil tests good there. I guess it comes down to compression or timing. But, I'm assuming the timing is good as long as the flywheel is aligned with the key.
 
Last edited:

Icecube3456

Cadet
Thread starter
Joined
Aug 7, 2017
Messages
10
How do I adjust the throttle cam? I'm pretty sure it's out of adjustment because with the start lever all the way back the roller is about 1/2" above the line on the cam.
 
Last edited:

Icecube3456

Cadet
Thread starter
Joined
Aug 7, 2017
Messages
10
Still no good. It starts but has no power. I guess ill have to wait until Saturday to get the compression meter
 
Top