18hp Evinrude mis-firing, also need year

seanrh

Recruit
Thread starter
Joined
May 30, 2003
Messages
4
I have a good condition 18hp evinrude # 18702R E02862. I'm not sure of the year and cannot determine it based on previous posts from others. Also this engine had been completely gone through by an outboard mechanic before I got and it runs fine except for it misses every 10-20 seconds. Any help would be great.<br /><br />Thanks in Advance
 

Hooty

Rear Admiral
Joined
Oct 2, 2001
Messages
4,496
Re: 18hp Evinrude mis-firing, also need year

Howdy Sean and welcome to iboats.<br />Your engine is a 1967 18hp. You're gonna have to tell us a little more about the miss before anyone can help.<br /><br />c/6<br /><br />Hooty
 

seanrh

Recruit
Thread starter
Joined
May 30, 2003
Messages
4
Re: 18hp Evinrude mis-firing, also need year

Thank you hooty for the year info. I'm not sure how to go into more detail on the mis-firing. The engine starts great and idles and runs at higher rpms. But at all rpms every 10-20 seconds it basicly skips a beat, the engine jerks and then it keeps going at the same speed it was. It just cuts out for less than a second. Not sure how else to describe it. Plugs are good, gas is good.
 

dkondelik

Chief Petty Officer
Joined
Sep 10, 2002
Messages
643
Re: 18hp Evinrude mis-firing, also need year

'evening Sean,<br /><br />is your "miss" more prominant at lower rpm? Does it idle ok? could it be described as a sneeze? if it is more obvios at lower R's it could be a simple idle mix adjustment. just open the idle mix screw 1/8 to 1/4 of a turn and it should get bettter. if this is the problem, let it run for a while after the 1/8 turn adjustment to let the fuel work its way through.<br /><br />Let us know what you find. if this isn't it, there are some other possibilities.<br /><br />Good Luck
 

lewkster

Seaman
Joined
May 25, 2003
Messages
60
Re: 18hp Evinrude mis-firing, also need year

Hi, I have a 1968 18 hp evinrude. Just overhauling carb. In the process of over hauling and resetting everything, I ran into same thing.<br />What I found is if it misses at lower rpm's (if your motor is same as mine, and theres a lean rich screw in front over motor next to kill switch). Turn it towards richer mixture. Just a tiny bit!!! Let it run for about a minute it really does take time for it to adjust the gasses thru the motor. Hey I would be interested in learning what your going thru with your motor also. I just bought this myself.Runs so nice. contact me at dabrjomn@aol.com. P.S. if you end up over hauling carb. the setting of the float inside carb I am learning is very titley related to how that lean rich screw adjustment is made.It's been a process since it was trail an error maybe save ya some time if ya go that route.
 

tombold

Cadet
Joined
Apr 29, 2003
Messages
15
Re: 18hp Evinrude mis-firing, also need year

Hi,<br /><br />I have a 1975 25 HP Evinrude that is doing the exact same thing that you are talking about. I have been monkeying with the rich/lean it worked. But it did it again the next time out so I have to constantly adjust.
 

seanrh

Recruit
Thread starter
Joined
May 30, 2003
Messages
4
Re: 18hp Evinrude mis-firing, also need year

Thanks for the advice, I am taking the boat out today and going to try the adjustments mentioned. I thought that it might have something to do with that rich/lean low idle switch but I don't think that I gave it enough time when I was adjusting it. I'll let you know what happens today.<br /><br />Sean
 

seanrh

Recruit
Thread starter
Joined
May 30, 2003
Messages
4
Re: 18hp Evinrude mis-firing, also need year

Just thought that I would update on my mis- problem. Looks like it is the rich/lean low idle knob that did the trick. I do have to do small adjustments almost every time I take it out but once that is done it runs like a champ.<br /><br />Enjoy the water!<br /><br />Sean
 
Top