Search results

  1. W

    Submerged 6hp merc

    any suggestions on what proper steps have to be taken to clean the motor up to get it running again? Thank you for any help you can give me.
  2. W

    rescipe for northern pike

    Does anybody have a recsipe for northern pike fish patties? Thanks for any help
  3. W

    Need help on a Eagle fishfinder

    Hi all, I would like to know if anybody knows how to take apart a Eagle Ultra III Plus fishfinder? I had moisture inside of the screen. The finder works great, but I can't see the image on the screen. I called the factory and they said that they don't repair that older model. It seems a shame...
  4. W

    Steel sleeves in mercury

    Hi all, what years did merc 150's have steel sleeves in them. Thank You
  5. W

    I need a paddle wheel speed sensor

    Hi all, I need a paddle wheel speed sensor for a Eagle Ultra III plus or a Lowrance X55. Thank You
  6. W

    merc_nut

    Hi all. Anybody know how to get a hold of merc_nut or have his email address. I know he is on the marine doctor forum and I thought I seen him post on here before. I need to ask him a question about the marine doctor forum. Thank you for any help you can give me . Woodchuck
  7. W

    trim gauge

    My trim gauge on my 84 merc 150 quit working.Where should I start looking for the problem? when I push the trim button the needle will barely move. Thanks for any advice.
  8. W

    heat horn not working

    I have a 1984 merc 150, took the oil injection off, now the warning horn or buzzer dosn'tsound when I turn the key on. Thanks for any help that you give me. Woodchuck
  9. W

    50 to 1 oil mix

    how many ounces of oil per gallon for 50 to 1 oil mix
  10. W

    intertube for 8 or 12 inch boat trailor tire

    Anybody know where I can buy A INTERTUBE FOR A 8 OR 12 INCH TIRE FOR ABOAT TRAILER? Thanks
  11. W

    thrusher washer

    what is the purpose of a thrush washer?
  12. W

    vent holes in prop

    I have 84 mercury 150 on a 84 17 ft hydra sport with a 14in. by 24p ss prop. how big of a vent hole can I drill without hurting performance? thanks
  13. W

    Pennzoil synthetic blend oil

    Hi, I have a 1984 merc 150 black max, I have always used merc oil. Can I use pennzoil synthetic blend oil without harming my engine, or another synthetic oil? Thanks guys
  14. W

    50:1 oil mix

    How many ounces of oil to 1 gallon of gas for 50:1 mix? Thanks guys
  15. W

    mercury parts express

    I get on mercury parts express and it is differnt than it was the last time I was on it. I can not get into merc engine parts. I don't know if I'am doing something wrong or I'am just to dam dumb. Is anybody else having this problem? thanks guys
  16. W

    enrichner vale

    How do I check to see if the enrichner valve is working properly? It does not click. The choke at the key quit working. I installed a push button and wired into the wiring harness about 3 years ago,this spring the enrichner valve quit working, also I tried to get into mercuy parts express, I get...
  17. W

    remove prop shaft and gears

    Hi guys, how do you remove the prop shaft and gear assembly, do I need special tools, does the lower unit have to come off? Thank you
  18. W

    reverse is gone

    Hi all,when I put gear shift in reverse, it makes a heck of a noise. Can anybody give me a rough estimate to get repaired. The motor is a 1984 mercury 150 black max. Thanks in advance.
  19. W

    trigger assembly

    Hi all.I've got a 84 mecr 150 black max,when I put hammer down,it acts like it is loaded up on gas, it spuders a little while,then take off and runs good.Is this in the carbs or may be the trigger assembly? Thanks in advance.
  20. W

    trim motor wiring

    Hi all ,I need to extend the + and - wires on my trim motor, which would be the best and safe way to do this? Need to extend 3 feet. Thank You
Top