Search results

  1. K

    Etec Gear Oil

    Wondering what the story is with ETEC gear oil. Do I need to change like the old models to insure that there?s no water in the gear case. Motor has been used one season with outside winter storage? Also, what about those fuel additives I used to add. 2-4 , carb guard, etc. Should I be...
  2. K

    Etec Throttle Cam (2007 150)

    I bought a 2007 150 ETEC leftover this year and have had the computer upgraded for the latest program, which smoothed things out. However, my throttle is still a little jumpy and very sensitive, won?t hold RPMs - than jumps when you move it back up (3200 to 3800 RPMs). I?ve read somewhere that...
  3. K

    Etec 07 VRO Help

    Hay guys I bought a left over Etec 150 - 2007 and I have a problem. :( The VRO no oil light comes on after I get it in the water after one use. Oil ran thought the houses during set up and test start no problem. I checked the Oil at the connection joint and after the oil filter when primed...
  4. K

    Etec Prop

    Hay I just picked up an Etec 150 2007 left over. What prop should I get for a 212 Neptune by sunbird Boat is the same as the 212 hydrasport walk around. I think I had a 15 x 17 before - maybe a 15.5 x 17. What happens if I go to a 14.5 x 17 or 19 Your thougts if any?? Thanks:redface:
  5. K

    Battery - Etec 150 2007

    I have a 2007 out of the box Etec 150 and I?m wondering about batteries. I?ve always used regular car batteries once my marine battery went bad. I get more years and have had no problems using with my older model 150 (1996). So what I?m wondering is can I do the same with the new Etec. I've...
  6. K

    hoisting an Etec 150

    I?m looking to find out how to hoist a 2007 Etec 150 HP. I?ve been told to screw into the cam shaft at the top of the motor. Theres 3 places to screw into one dead center and 2 others in line with center. Is there a special tool ? or will any eye bolt do the job. Please advise
  7. K

    Not the DOG

    I?m back Hope you?re out there High Trim. Well I pulled the lower unit with high expectations that my shift/clutch DOG was my problem. Not the case. DOG and gear show no signs of wear. I do have some problems with some seals - outer drive and the one under the water pump, but that looks...
  8. K

    Stator check

    how does one check the stator to ensure its working. I have a miss under load after reaching 3800 RPMs, but depending on load can be even high RPMs Changed everything, but stator.
  9. K

    Johnson oceanpro 150 missfiring

    Johnson Oceanrunner running poorly: No answers to date: Engine seems to skip a beat at 3,800 ? 4,000 RPMS sometimes a lot higher and sometimes not at all, but most of the time it will miss. When I pull back it immediately goes away Already replaced Eye sensor Coils Wires Plugs Pack Gas...
  10. K

    Optical sensor install 150 johnson

    does anyone know how to install the optical ignition sensor on a 150 johnson oceanrunner. It's visable right on the side of the fly wheel, but underneath it and looks like it's screwed from underneath as well.
  11. K

    Johnson oceanpro 150 missfiring

    hay 1996 150 first problem ever: misfiring at 4000 - 4200 RPM's starts well ran good @ first plane 3000 -3200 RPM's. I've checked gas no water in seperator. Did Alcohol check as well 8-10% put 2 different innition packs on one with coils and wires one just the pack (used of course) just to...
Top