Search results

  1. Dshow

    Oil change when winterizing?

    Hi all, I typically change both filters, the outdrive oil, and the engine oil each year when I winterize. This year, since my folks got a new boat, I have only had mine out a couple of times so it probably has about 5 hrs on it this summer, otherwise, it sits in a pole barn. Do I change the...
  2. Dshow

    What are these wires?

    Hi all, my folks juist bought a used boat. It's a 2001 Crownline 192BR with a 4.3 Thunderbolt V ignition, SN OL642375. It ran great when I took it out, but looking at the engine, I noticed there were two wires hanging loose... One is a black wire I'm guessing is gnd and the other is a purple...
  3. Dshow

    Does the remote shift cable need adjusted?

    I have an Alpha 1 Gen 2. Recently replace the shift cable to the outdrive because I was replacing bellows but everything was working fine. I did not touch the remote shift cable to the throttle. Do I need to make any other adjustments other than the lower shift cable? Thanks
  4. Dshow

    How big a PITA is replacing the gear oil fitting on transom?

    Long story short, removing the bell housing to replace the bellows on my alpha 1 gen 2. Yes, I should have cut gear oil hose, but did not... Cut the tie wrap on the plastic right angle transom fitting and tried to get the hose off. Worked and worked, finally the hose barb snapped. It's off...
  5. Dshow

    When to use bellows adhesive?

    Hi all, I've been lurking on this site for several years and have learned a vast amount of information, thank you all... I have an Alpha 1 Gen II outdrive that I will be replacing the bellows shortly. I have both Power tune and Sierra Bellows Adhesive. The Merc manual says use adhesive on one...
  6. Dshow

    Bellows replacement sequence...

    So I will be replacing the bellows and shift cable on my boat that has an Alpha I Gen2 outdrive this off season. (Thanks millenium3 for your video) I've got the Merc service manuals so I will get the details from that, but just want to get the sequence correct in my head of what works the best...
  7. Dshow

    What can you tell me about this? EGR?

    I have a 2001 Mercruiser 5.7L EFI. On my starboard exhaust manifold, there is a tube that goes over to the intake manifold. I assume it's some sort of EGR? Does this just supply exhaust to the intake all the time? What's the purpose of this? Thanks!
  8. Dshow

    Quick bellows questions

    Hi all, I'm thinking it's about time to change all the bellows on my boat (Alpha 1 Gen 2 outdrive). I've noticed you can buy kits with and without the gimbal bearing. I have no issues with my present bearing and I'm familiar with pulling off the outdrive. Is this something I can replace at a...
  9. Dshow

    Trim pump motor?

    Hi all, I have an Alpha Gen2 outdrive. How often is there intermittent issues with the trim pump motor itself? Went to get the boat for the first time of the season. I have trim switches on the transom as well as the throttle lever. When I went to raise the drive to trailer it home with the...
  10. Dshow

    Update to "How to ask a question thread"?

    I've been following several threads and I've noticed that once several suggestions are made, the OP disappears and is never heard from until they have a different issue. It sure would be nice if once they found a solution, they would update the thread with what fixed the issue and mark it as...
  11. Dshow

    Alignment tool variation?

    I've read many posts about people trying to align their engine but not being sure if the engine needs to go up or down. I've aligned my engine, but not really sure the tool slides in as easy as it's supposed to. Do they make a tool that is the correct diameter of an alignment tool for the...
  12. Dshow

    Another alignment question...

    Ok, so have read many alignment threads and know the alignment bar is supposed to slide in very easy... When winterizing, I adjusted the front motor mounts to get the alignment bar to slide in as easy as possible. When putting the outdrive back on, it would go in past the gimbel bearing, but...
  13. Dshow

    Front engine mount nut size

    I'm getting ready to align my engine. I have a 2001 Merc 5.7. I have a 1 1/16" wrench, but it is slightly to small. Does anyone know the exact size? Thanks-
  14. Dshow

    MEFI-4 Information (davsboater)

    For MEFI-4 information, check here -> http://www.pirate4x4.com/tech/billavista/MEFI/MEFI%204%20&%204B%20DIAGNOSTIC%20MANUAL%20(L510005P).pdf
  15. Dshow

    Serpentine Belt P/N?

    There been alot of posts regarding serpentine belts lately which has me thinking I should probably change mine. I have a 2001 Mercruiser 5.7L TBI, s/n 0M080869. Does anyone know the part number for the belt I need? Thanks!
  16. Dshow

    Coupler greasing same as greasing the spine?

    2001 Mercruiser 5.7L, Alpha I Gen II... In the engine compartment, there is a grease fitting on the output of the engine on what I believe is the shaft that is a PITA to get to. When I have my drive off, I grease the splines before reassembly... Are these points one in the same or do they both...
  17. Dshow

    Generally, when do you use anti-sieze?

    I'll be pulling the risors off my engine this winter and was wondering, when I put them back on, should I use anti-sieze on the bolts? In general, when is this used? Exhaust system components only? Any bolt that looks corroded and you don't want to get stuck? All bolts? Thanks- Dshow
  18. Dshow

    2 small gaskets in Alpha1 Gen2 water pump kit?

    There are two small gaskets that are the same size that are included in a water pump repair kit for an Alpha 1 Gen2 outdrive. (Right below the pump housing in the picture) Where do they go? Thanks-
  19. Dshow

    Necessary to use gasket sealer on impeller gaskets?

    I have replaced the impeller on my Alpha 1 Gen 2 outdrive a couple of times. The manual says use Perfect Seal gasket sealer on the two impeller housing gaskets. I have the equivalent Permatex Aviation gasket sealer that is applied with a brush, but I think that would make a mess and get sealer...
  20. Dshow

    Would a blown head gasket show up other places?

    I have a 2001 5.7L TBI Mercruiser that I've had for 3 seasons. Ever since I've had the boat, I've had a steam issue out the starboard thru-hull exhaust. (Typically, after a hard run.) This has never caused an issue. The engine has never over heated and stays ~165F according to the gage no...
Top