Search results

  1. Y

    79 DT25 Ignition Coil

    The ignition coil for this motor has been DISCONTINUED. Does anyone have any ideas on replaceing this thing. Is there another year or model coil that will work. Please help!!!
  2. Y

    Random Sneeze!

    1973 Evinrude 25, Just wondering what causes a sneeze! It does this at idle only sometimes. No other problems, as far as I know! Thanks
  3. Y

    Armature Plate Repair

    Hello, I done the Joe Reeves repair on the armature plate and the slack seems to be gone. When I started the motor, It seemed as though It was idleing higher than before. It has good throttle response and idles good, but maybe alittle high. Does this sound normal? Can I adjust the idle on this...
  4. Y

    Evinrude Coil Wiring

    This is a 1973 25 Evinrude. From the armature plate there are two wires with plugs on the ends of them that hook to the coils. Can you hook either coil to either wire coming from armature plate.? They appear to be the same as if it doesnt matter!
  5. Y

    Armature Plate? (25 Evinrude)

    Well, took this motor out today(79 25 Enivrude) after alot of work and it ran great, but idles alittle rough. Local outboard shop said these motors were bad about the armature plate retaining ring(#12) getting worn and in return, alot of movement in the armature plate which shakes the points...
  6. Y

    FROM KEY START TO PUSH BUTTON!! Evinrude

    This is a 1973 Evinrude Elec start. The present key switch has 5 wires. 1 to elec choke, 1 to top of solonoid, 1 to bottom of solonoid and 1 to each coil(2). Is this possible? I have a 2 terminal push button switch. If possible, what would I need to do? I was thinking of also putting a small...
  7. Y

    1973 25 Evinrude (Head Bolt Torque)

    Just wondering if anyone knows the head bolt torq spec for a 1973 25 Evinrude. Thanks
  8. Y

    25 Evinrude De Carbon?

    I was wondering if there's anything easier way than carb cleaner and a wire brush to de carbon a motor. Head is already off due to a new head gasket. I have lots of build up. Probably first de carbon since 1973!!
  9. Y

    1973 Evinrude 25 (Timing Check)

    Just wondeing what the process is for checking the timing on this motor(73 Evinrude 25). Don't think its out but wanted to check it anyway??
  10. Y

    1979 DT25 Suzuki Parts! Parts! Parts! Help!!!

    Still looking for some ignition parts. Need CDI, Stator Coil, Ignition Coil and whatever else I can find!! Anyone know any used parts resources!!! Thanks
  11. Y

    Debris In Thermostat Housing!!!

    I was changing the thermostat in my 1973 Evinrude 25 and noticed some medium sized pieces of what looked like carbon. I had been have trouble with overheating and decided to change t-stat and water pump. Should I be concerned or could this be from setting up for a long time?? Are there any areas...
  12. Y

    1973 Evinrude 25 Point Set (Pics)

    Could someone please get me on the right path to checking the points on this motor. I am changing upper oil seal and wanted to check the points. Flywheel says 0.020 Thanks
  13. Y

    1973 Evinrude 25 (Upper Crankshaft Oil Seal) &

    Just wondering if it is a big project to change the upper crankshaft oil seal. I also have a suzuki and its not much trouble. Just a matter of removing flywheel, stator assembly and a plate that has the seal in it. Noticed on this motor it doesnt look so easy. Thanks Alot
  14. Y

    1973 Evinrude 25 (Running Hot)

    I recently purchased this 73 Evinrude 25 and took it out today. Motor runs great, starts fast, but, after pulling out, I noticed the hood was very warm. Pulled the hood and there was (some) steam rolling off the motor. Seemed to be pumping great while running, but it was also very hot to the...
  15. Y

    1999 1750 Bayliner Capri Deiseling? (3.0 Merc)

    I purchased this boat in 2002 and this boat has always dieseled. This mainly happens after shutting down after running a long distance. Boat has been very well maintained and always good gas. New plugs evey year and recently new wires. Timing Maybe??
  16. Y

    1973 Evinrude 25

    I am looking at buying a 1973 25HP evinrude electric start to put on my 14' 44" flat bottom. Is there anything I should be aware when looking at this motor? Motor starts right up by recoil or electric. Seems to run great. What kind of commpresion should this motor have? What should be a fair...
  17. Y

    New pressure tank or convert to fuel pump????

    I have sprung a few leaks in my old pressure tank and was thinking of doing one of two things. Either converting to regular fuel pump, or takeing the actual pump assembly out of the old tank and finding a plastic tank that is flat enough on top and cutting out and installing the old tank...
  18. Y

    Suzuki Parts (Rodbolt)

    Rodbolt, I posted the 79 DT25 Overhaul Thread, I am neading a CDI, Stator Assembly and ignition coil. I saw where the other guy couldn't use the CDI and I was hopeing I might could get it. My email is yelladog@charter.net Thanks Alot,Brian C.
  19. Y

    59 Evinrude Fastwin 10HP (Need Part!!!!)

    I have aquired a pretty nice Vintage Evinrude and need a pinion gear. I believe that is what is called. It is the gear that rides on the end of the main drive shaft from the powerhead to the foot. Does anyone know where I might find one of these. Also, any info about this motor would be...
  20. Y

    79 DT 25 Overhaul Please Help!!!!!!!!!!!!!

    Ok here I go, This motor was running pretty good, but did not run as strong as it did when I got it. I decided to install new pistons and rings and just basically go through the motor. The problems started early when I broke a bolt off in the top of the flywheel. Decided to drill the bolt out...
Top