Search results

  1. 3

    Tell tale not peeing

    Thanks for all the advice! I took her to the lake today and it peed just fine. I’ll try some of the ideas including the tape. I wonder if just need to turn my muffs 90 degrees
  2. 3

    Tell tale not peeing

    A little update. Per some reading up, I took the boat down to the boat ramp, backed it in, and the tell tale worked! What is going on? I won’t have a chance to hook it back up to muffs until tomorrow morning to see if it knocked a clog out or whatever. But is this a thing? There is a hole...
  3. 3

    Tell tale not peeing

    I have a new to me 2018 Mercury 150 4 stroke. I just bought the boat and I saw the tell tale peeing when I test drove it. After I got it home I immediately replaced the impeller and the thermostat. I fired it up today on muffs and now the tell tale doesn’t tell any tales. I have removed...
  4. 3

    Fish finder and terrova combo help

    Thanks for the replies!
  5. 3

    Fish finder and terrova combo help

    I’m getting exhausted trying to figure out what trolling motor/fish finder combo I want. Anyone want to share their opinions? I have a 2018 tracker 2072 and fish Oklahoma lakes for bass, striper, white bass, and catfish. I’m about to put a terrova on the bow. But should I spend the money on...
  6. 3

    Shift rod won’t go back in

    Hello all. I am replacing a bent prop shaft on my new to me 2018 Mercury 150 4 stroke. During disassembly, the shift shaft was difficult to remove from the lower unit. Now during assembly, the shift shaft won’t go back in. It seems to get bound on something about 5/16 short of being seated...
  7. 3

    Creaking/popping power trim

    So since the ram was leaking a bit, I ended up pulling the whole thing off to replace some seals in the ram. In doing so, I found there was some rust in the bottom pivot pin. I am pretty sure that was the source of the sounds. I greased the pin up and re assembled, no more noise. I wish I...
  8. 3

    Creaking/popping power trim

    Back from a great vacation. I tried just squinting some pb blaster on the joints and it smoothed up pretty good. But per my usual course, my neurotic nature got the best of me and I removed the whole thing to replace the seals. So here we go with
  9. 3

    Bent prop shaft

    And never mind on Q2: i got impatient and ended up wrapping the shift shaft in a towel and clamped on some vice grips, then tapped (ok more than a trap) the vice grips aggressively and the bushing reluctantly came out.
  10. 3

    Bent prop shaft

    Ok, never mind you story installs confidence. Thanks!
  11. 3

    Bent prop shaft

    I got the gearcase open. The nut and bearing carrier came out easy peasy (nothing ever goes that well for me, so now I’m nervous). All the gears look to be in good shape no visible wear or brinelling. Q1: should I replace any of the bearings? Everything seems to spin smooth and is...
  12. 3

    Creaking/popping power trim

    Thanks, the fam an I went on vacation this week, when I get back I’ll see if I can isolate the sound to those areas. Hopefully just some wd-40, as you say
  13. 3

    Creaking/popping power trim

    Right!? But I looked in all the usual places. The swivel has a zerk. So far, the only zerk I have found. Maybe the tilt tube has sealed bearings?
  14. 3

    Creaking/popping power trim

    I don’t think so. The previous owner said no, but he also failed to mention the severely bent prop shaft that I overlooked, but I’m confident he was aware of. But i bought the boat in east Texas, so certainly plausible
  15. 3

    Creaking/popping power trim

    Certainly a chance. I ran it up and down several times, assuming that was the source, but I just couldn’t get a positive ID. But like I said, there doesn’t seem to be any means of greasing the tube
  16. 3

    Creaking/popping power trim

    My new to me 2018 Mercury 150 four stroke makes a creaking/ popping sound when I raise and lower the motor. I can’t seem to isolate the sound, but I think it might be coming from the power trim hydraulic ram. That being said, I can’t find a single grease zerk on the thing. The parts diagram...
  17. 3

    Bent prop shaft

    Im going to keep my fingers crossed that boscoe99 is right, and that it’s just the shaft. 😬
  18. 3

    Bent prop shaft

    Yeah, just one though. It was a 1985 Suzuki dt65. Seemed pretty straight forward. Any reason to believe this one will be more complicated or difficult?
  19. 3

    Bent prop shaft

    All wise words. Thank you all for the advice. I’ll get her cracked open in about two weeks and see how those gears and bearing surfaces are doing and go from there. You all are great. Thanks!
  20. 3

    Bent prop shaft

    I had to google brinelling. Thanks for the new word!
Top