Search results

  1. S

    Needing help ID'ing a leak location, pls. 1992 Johnson 140 Looper V4

    Got it. Thx. I was just concerned because it's never done that on the muffs before, and there was a lot of it leaking out of there. Since it happened right after I ran it with no water for a minute, I thought I'd blown a seal. I'll still be replacing the whole water pump assembly and upper/lower...
  2. S

    Needing help ID'ing a leak location, pls. 1992 Johnson 140 Looper V4

    Ok... Since it's simple, hopefully you can answer this for me. Is the sludge normal or no? What can be done to prevent it? and does it mean I have an issue that needs addressing in the engine or with my fuel?
  3. S

    Needing help ID'ing a leak location, pls. 1992 Johnson 140 Looper V4

    Ah... So as I'm understanding it, my issue with all that sludge isn't the water pump at all, but rather just unburnt fuel/oil mixing with the gas. Correct? It's never done this before... so is it just something that happens from time to time or is something wrong with my motor that causes this...
  4. S

    Needing help ID'ing a leak location, pls. 1992 Johnson 140 Looper V4

    Which gasket/o-ring is it that stops that from happening? I'm already going to be getting all the ones others have mentioned but just for my own knowledge I'd like to know. Number of it on the diagram would be great if you know. Thanks for the reply!
  5. S

    Needing help ID'ing a leak location, pls. 1992 Johnson 140 Looper V4

    Which parts on the diagram are those?
  6. S

    Needing help ID'ing a leak location, pls. 1992 Johnson 140 Looper V4

    Ok. No problem. On this pic could someone tell me what exactly the diagram numbers are I need to buy other than the impeller and housing?
  7. S

    Needing help ID'ing a leak location, pls. 1992 Johnson 140 Looper V4

    1992 johnson 140 looper (v4). Got out there to do some maintenance today, and decided to run the engine a bit on the muffs since it's been a couple of weeks and I didn't fog it yet this winter. In my haste, I completely forgot to turn on the ON lever at the muffs and ended up running it for...
  8. S

    1992 Johnson 140 Looper install fine tuning questions. Rough idle/stalling after install.

    Also, what is the "idle circuit". I've been studying up on all the linkages, but didn't know there was a "circuit" involved.
  9. S

    1992 Johnson 140 Looper install fine tuning questions. Rough idle/stalling after install.

    I understand... And I have the original service manual. The problem was just trying to figure out what I should look at first. Maybe something I should check BEFORE going through the whole process of resynching. Only trying to avoid it as theres a few parts of the instructions I dont understand...
  10. S

    1992 Johnson 140 Looper install fine tuning questions. Rough idle/stalling after install.

    Compression reads 120 on all 4 cyls.
  11. S

    1992 Johnson 140 Looper install fine tuning questions. Rough idle/stalling after install.

    Racerone: It was a bit rough to start on his boat due to really cold water, but once it got warmed up after a minute or two it ran pretty smooth. I've only had it out one time on my boat and it ran fine when in gear and did idle in neutral most of the time, but the idle was a bit choppy and...
  12. S

    1992 Johnson 140 Looper install fine tuning questions. Rough idle/stalling after install.

    .
  13. S

    1992 Johnson 140 Looper install fine tuning questions. Rough idle/stalling after install.

    Thx for the step by step. I'll be trying to tackle this at some point this week. Just a couple questions to make sure I get this right... I've circled the screw I believe to be the idle adjustment screw in a pic of my engine I found online. Is that correct? Also, is the link n synch where I...
  14. S

    1992 Johnson 140 Looper install fine tuning questions. Rough idle/stalling after install.

    I do have the service manual which the original owner gave me when I bought it, but some of the lingo they use is confusing to me. To follow it to a tee, I'll have to teach myself how to use a timing light. In order to increase or decrease idle speed on my motor, is the easiest way just to...
  15. S

    1992 Johnson 140 Looper install fine tuning questions. Rough idle/stalling after install.

    Thx for confirming that, man. Would you recommend adjusting the idle speed screw then, or checking something else? I'm thinking the issue has to be with the way it was setup on my boat when switched over or the fuel I have might just be super old (no way of knowing)... I do know it smells like...
  16. S

    1992 Johnson 140 Looper install fine tuning questions. Rough idle/stalling after install.

    Still trying to figure this out... I searched out the issue on the forums a bit and am seeing that my symptoms could also be something called the "Shift Interrupter Switch". I've searched the parts manuals for my motor head to toe and can't seem to find where this part is located or the part...
  17. S

    1992 Johnson 140 Looper install fine tuning questions. Rough idle/stalling after install.

    Hi all. Just had a 92' Johnson 140HP Looper installed on my 86 Hurricane FD196. The gentleman that sold it to me installed it and did all of the throttle linkage connections while once it was moved over from his boat. After letting the sealant we used dry for a week, I took it out on the water...
  18. S

    Strange overheat issues. Melted my check valve...

    Evening all. Welcome to the latest edition of "Still trying to get this 86 E150 water ready". Just went outside after work today to add rtv sealant to both hermostat housing gaskets to stop the leaks from where I installed them without it last week. When I first got the boat I had found that...
  19. S

    Does this sound like its running alright?

    1986 Evinrude 150. I've only had one 40hp Nissan before this and it was recently serviced without any issues... This one I've had to put a bunch of TLC into in order to get it to where I feel safe finally taking it out. Now needing someone with more knowledge to give an ok on it... Could...
  20. S

    Need red rtv for thermostat housings?

    Just installed new tstats and valves on my 86 e150. I put in the new gaskets and tightened it all down. Now it has some drops of bubbling water coming out on each side. Maybe take it back off and apply rtv to each side of the gasket? Don't want to over tighten the bolts as they aren't in the...
Top