Search results

  1. F

    1976 35h.p, Evinrude lower unit rebuilt now not working

    I rebuilt the lower unit last fall for an older gentleman with the forums help (Thanks) I replased the clutch Dog Forward gear and it ran for last season. Replased gear lube in the fall and it ran well for a dozen times this year and now it is kicks in and out of gear again. IT seems as if you...
  2. F

    Help finding service manual

    Just bought a new boat with a 115 Johnson outboard motor mod#L115GLEDC Ser#G04113252 CE 96. I am assuming it is a 1996 but not sure. I have found two OEM manuals but not sure which to buy. <br /><br />1) 90,115,1250,150c,175 hp 60 degree LV<br /><br />2) 88,90,100,112,115 hp 90 degree V<br...
  3. F

    Forzen Water damage??

    Just recently purchased a 95 115h.p. Johnson on a Lund Tyee. The guy I purchased it from showed it to two other people and used the Suction cup water supply for proving the engines performance. He also demonstated it to me. The engine stared right up and ran fine with a good stream of water...
  4. F

    Forzen Water damage??

    Just recently purchased a 95 115h.p. Johnson on a Lund Tyee. The guy I purchased it from showed it to two other people and used the Suction cup water supply for proving the engines performance. He also demonstated it to me. The engine stared right up and ran fine with a good stream of water...
  5. F

    Which sealant for Exhaust gasket?

    I will be replacing the lower gasket on the powerhead that connects to the inner exhaust tube on a 76 35hp. I need to know what kind of sealant to use. The manual calls for OMC gasket sealing compound. I cannot find this and need a substitute.<br /><br />Can I use permmatex Indian Head Gasket...
  6. F

    Is boat/motor worth buying?

    Looking to buy a used fishing boat with a 02 50hp EFI 4 stroke Evenrude motor. It runs fine in low to mid throttle but when it is run up it starts to miss and lose almost all power. For a 02 it looks like this boat and motor has been dock negleted. Not allot of hours on the boat but has been...
  7. F

    Could my indash tach be defective?

    I am running a 25h.p. Bigfoot that only maxes out to about 4500 rpm's. I think wide open is about 5600 r.p.m's. I changed to a Pontoon prop since it is on a pontoon and did not notice a great difference in rpm's. <br /><br />My question is before I go to adjust the remote should I make sure...
  8. F

    Lower Unit - Spring and Ball indent - R.Johnson

    I am rebuilding my 1976 35 Evinrude. I can reasemble the two balls, spring and clutch dog by hand but I am figuring that the notch in the OMC tool must be there to do the proper allinging. I know that R.Johnson said that you may be able to make this sleve tool. But I am wondering on this...
  9. F

    Tough lower unit question 35hp 1976 Evinrude - "Please help J. Reeves"

    I have a 35hp long shaft 76 Evinrude that is kicking out of forward gear at about one third throttle. It kicks out of reverse at about one half throttle. When I went to drop the lower unit to rebuild I noticed that the lower connecting rod bolt was different than the top and think that it may...
  10. F

    1998 750 Kawasaki needs priming

    I cant get my 98 750 started without pouring a cap of gas in the throats of the carbs. I have adjusted the choke but does not help. Does anyone have any sugestions?<br /><br />Thnaks<br /><br />Mike
  11. F

    1976 35hp gear part numbers?

    I am looking for the part numbers of the pinion forward and reverse gear of the above mentioned lower unit.<br /><br />If you have them for sale let me know. New or used.<br /><br />Thanks<br /><br />Mike
  12. F

    Year of Evinrude 35hp model 35653G?

    Looking for the year of a 35 h.p. Evinrude Model 35653G or 356536? Dont know if last digit is a 6 or a g?<br /><br />Thnaks<br /><br />Mike
  13. F

    late 70's 35 h.p. kicking out of gear

    My 35 h.p. Evinrude is kicking out of gear in both forward and neutral at about 1/3 throtle. Checked linkage cable and this is not the problem. While shifting manually it still does it. What do you think is the culprit? What should I check next? <br /><br />Serial number is 10003957. Anybody...
  14. F

    Will 1960 lower end work on 1957 10h.p. Evinrude?

    Can I put a 1960 lower end on a 1957 10 h.p. Evinrude. There is the small phillips screw on the skeg on the 1960 and not the 1957. Will this make a differance. Also could I use the the whbole lower including the exaust port down?<br /><br /><br />Thanks<br /><br />Mike
  15. F

    Points overhaul question 1957 10h.p. Sportwin

    I have replaced points, condensor, and coils on this 10h.p. Sportwin. When I installed it back on the motor with the cam in place I tried to adjust the points to .020 with the flywheel off according to the manuals directions. After many attempts I was unable to get the points to open enough to...
  16. F

    Crankcase Gasket sealer?! Which one?

    Can I use 3M Scotch-Grip Rubber & Gasket Adhesive 847 in the upper seal of my 1957 10h.p. sportwin? I cant seem to find OMC gasket sealer.
  17. F

    1957 Sportwin Cam Wick

    Can anyone enlighting me on how to replace the cam/points wick in these engines? I know the procedure on how to remove and replace. But are you suppose to add oil to this wick? And if so what kind? What should I be aware of?<br /><br />Thanks
  18. F

    1957 Sportwin 10h.p. Which sealants to use?

    I have recently purchaced a 1957 10h.p. I have found out that almost everything that can wear is worn out. (Except it has good even compression) So I am doing a complete overhaul of Magneto, upper lower crankcase seals, carburator and lower unit seals/pump. <br /><br />My question is what...
  19. F

    1957 Sportwin Sparkplug comparison

    What difference would a champion J4C vs. J6C plug make in my 10 h.p. Sportwin? Could I use either one? Which one runs hotter?
  20. F

    Small shavings on lower units fill screw bad?

    I changed the lower units lube on my 1998 25 h.p. bigfoot only to notice very very small metal shavings on the bottom fill screw magnet. They were so fine that when I rubbed it between my fingers I did not really feel any grit. But it was metal shavings because it kept sticking to the magnets...
Top